06-30-2012 05:43 AM - edited 03-16-2019 11:56 AM
HI All,
We are planing impliment SIP in our organisation for making Long distence calls .with present Setup we are using H.323 and PRI for making Calls. We need H323 and SIP at same time.
Please find the Our Network Diagram and Router Configuration.
Note: Our CCM Has no conectivity to internet.
Router Configutation:
=~=~=~=~=~=~=~=~=~=~=~= PuTTY log 2012.06.30 16:38:51 =~=~=~=~=~=~=~=~=~=~=~=
sh run
Building configuration...
Current configuration : 8338 bytes
!
version 12.4
service timestamps debug datetime
service timestamps log datetime
service password-encryption
!
hostname oh-rt2
!
boot-start-marker
boot system flash c3745-advipservicesk9-mz.123-26.bin
boot-end-marker
!
logging buffered 4096 notifications
enable secret 5 $1$AgBh$dCd1NSglSXBbZXmjcdO/I.
!
no aaa new-model
clock timezone IST 5 30
no network-clock-participate slot 2
no network-clock-participate slot 4
voice-card 2
dspfarm
dsp services dspfarm
!
voice-card 4
dspfarm
dsp services dspfarm
!
ip cef
!
!
!
!
ip domain name vmoksha.com
isdn switch-type primary-4ess
!
!
voice hunt user-busy
voice rtp send-recv
!
voice service voip
allow-connections h323 to h323
allow-connections h323 to sip
allow-connections sip to h323
allow-connections sip to sip
h323
sip
bind control source-interface FastEthernet0/1
bind media source-interface FastEthernet0/1
transport switch udp tcp
call service stop forced
!
!
!
voice class codec 1
codec preference 1 g711ulaw
codec preference 2 g711alaw
codec preference 3 g729r8
!
!
!
voice class h323 1
h225 timeout tcp establish 3
!
!
!
!
!
!
!
fax interface-type fax-mail
!
!
controller E1 2/0
framing NO-CRC4
clock source internal
pri-group timeslots 1-24
description for BSnl
!
controller E1 4/0
framing NO-CRC4
pri-group timeslots 1-31
description For Outgoing
!
controller E1 4/1
framing NO-CRC4
pri-group timeslots 1-31 service mgcp
description For Incoming BSNL
!
ip tcp synwait-time 13
!
!
!
interface Multilink1
bandwidth 256
ip address 172.16.16.45 255.255.255.252
ip tcp header-compression iphc-format
ppp multilink
ppp multilink group 1
ip rtp header-compression iphc-format
!
interface FastEthernet0/0
ip address 10.10.14.5 255.255.255.0
ip broadcast-address 10.10.14.255
ip accounting output-packets
ip nbar protocol-discovery
ip route-cache flow
no ip mroute-cache
duplex auto
speed auto
h323-gateway voip bind srcaddr 10.10.14.5
!
interface Serial0/0
description Circuit #1 initiating in India via Bharti
bandwidth 128
no ip address
encapsulation ppp
no ip route-cache cef
no ip route-cache
no ip mroute-cache
clock rate 2000000
ppp multilink
!
interface FastEthernet0/1
ip address 10.10.3.10 255.255.255.0
duplex auto
speed auto
no cdp enable
!
interface Serial0/1
description Circuit #2 initiating in India via BSNL
bandwidth 128
no ip address
no ip route-cache cef
no ip route-cache
no ip mroute-cache
clock rate 2000000
!
interface Serial0/2
description initiating in India via TATA
bandwidth 128
no ip address
encapsulation ppp
clock rate 2000000
ppp multilink
ppp multilink group 1
!
interface Serial0/3
no ip address
shutdown
clock rate 2000000
no cdp enable
!
interface Serial2/0:15
no ip address
encapsulation hdlc
isdn switch-type primary-net5
isdn incoming-voice voice
no cdp enable
!
interface Serial4/0:15
no ip address
encapsulation hdlc
isdn switch-type primary-net5
isdn incoming-voice voice
no cdp enable
!
interface Serial4/1:15
no ip address
encapsulation hdlc
isdn switch-type primary-net5
isdn incoming-voice voice
isdn bind-l3 ccm-manager
no cdp enable
!
ip forward-protocol nd
ip route 10.10.0.0 255.255.0.0 10.10.14.1
ip route 172.18.252.0 255.255.255.192 10.10.14.1
ip route 192.168.2.0 255.255.255.0 10.10.3.111
ip route 203.92.42.2 255.255.255.255 10.10.3.1 permanent
!
ip http server
!
logging trap errors
access-list 1 permit 10.10.3.18 log
access-list 1 deny any
access-list 2 permit 10.10.3.18 log
access-list 2 deny any
dialer-list 1 protocol ip permit
snmp-server community public RO 1
snmp-server community private RW 2
snmp-server location OH/BLR/IN/vMoksha
snmp-server contact ravinder@vmoksha.com
snmp-server enable traps tty
!
!
!
control-plane
!
!
!
voice-port 1/0/0
!
voice-port 1/0/1
!
voice-port 1/1/0
cptone IN
timeouts interdigit 3
connection plar 500
!
voice-port 1/1/1
cptone IN
timeouts interdigit 3
connection plar 500
!
voice-port 2/0:15
connection plar 500
!
voice-port 3/0/0
cptone IN
timeouts interdigit 3
connection plar 810
!
voice-port 3/0/1
cptone IN
timeouts interdigit 3
connection plar 500
!
voice-port 3/1/0
cptone IN
timeouts interdigit 3
connection plar 500
!
voice-port 3/1/1
cptone IN
timeouts interdigit 3
connection plar 500
!
voice-port 4/0:15
connection plar 500
!
voice-port 4/1:15
!
ccm-manager mgcp
ccm-manager music-on-hold
ccm-manager config server 10.10.14.11
ccm-manager config
!
mgcp
mgcp call-agent 10.10.14.11 2427 service-type mgcp version 0.1
mgcp rtp unreachable timeout 1000 action notify
mgcp modem passthrough voip mode nse
mgcp package-capability rtp-package
mgcp package-capability sst-package
mgcp package-capability pre-package
no mgcp package-capability res-package
no mgcp package-capability fxr-package
no mgcp timer receive-rtcp
mgcp sdp simple
mgcp fax t38 inhibit
mgcp rtp payload-type g726r16 static
!
mgcp profile default
!
sccp local FastEthernet0/0
sccp
sccp ccm 10.10.14.11 priority 1
!
dspfarm rtp timeout 60
!
dial-peer cor custom
!
!
!
dial-peer voice 3 pots
service mgcpapp
direct-inward-dial
!
dial-peer voice 4 pots
service mgcpapp
!
dial-peer voice 5 pots
service mgcpapp
!
dial-peer voice 3000 voip
destination-pattern 3...
session target ipv4:160.100.160.151
!
dial-peer voice 9999 voip
destination-pattern 9T
session target ipv4:160.100.160.151
!
dial-peer voice 6 pots
service mgcpapp
!
dial-peer voice 14 pots
destination-pattern 0T
progress_ind setup enable 3
progress_ind progress enable 8
progress_ind connect enable 8
direct-inward-dial
port 4/0:15
!
dial-peer voice 101 voip
destination-pattern 7..
session target ipv4:10.10.14.11
dtmf-relay h245-alphanumeric
codec g711ulaw
ip qos dscp cs5 media
no vad
!
dial-peer voice 102 voip
destination-pattern 8..
session target ipv4:10.10.14.11
dtmf-relay h245-alphanumeric
codec g711ulaw
ip qos dscp cs5 media
no vad
!
dial-peer voice 103 voip
destination-pattern 9..
session target ipv4:10.10.14.11
dtmf-relay h245-alphanumeric
codec g711ulaw
ip qos dscp cs5 media
no vad
!
dial-peer voice 104 voip
session target ipv4:10.10.14.11
dtmf-relay h245-alphanumeric
codec g711ulaw
ip qos dscp cs5 media
no vad
!
dial-peer voice 105 voip
destination-pattern 6..
session target ipv4:10.10.14.11
dtmf-relay h245-alphanumeric
codec g711ulaw
ip qos dscp cs5 media
no vad
!
dial-peer voice 106 voip
destination-pattern 5..
voice-class codec 1
voice-class h323 1
session target ipv4:10.10.14.11
incoming called-number .
dtmf-relay h245-alphanumeric
ip qos dscp cs5 media
no vad
!
dial-peer voice 30 pots
preference 2
destination-pattern *5T
!
dial-peer voice 77 pots
preference 2
destination-pattern *7T
!
dial-peer voice 29 pots
preference 1
destination-pattern *5T
port 1/1/0
!
dial-peer voice 78 pots
preference 1
destination-pattern *7T
port 3/0/1
!
dial-peer voice 2 pots
incoming called-number 8025053.T
direct-inward-dial
!
dial-peer voice 1 pots
description **** For Income Dial Peer***
incoming called-number .
direct-inward-dial
port 4/0:15
!
dial-peer voice 11 pots
description **For income dial*****
incoming called-number .
direct-inward-dial
!
dial-peer voice 45 pots
preference 2
destination-pattern *8T
!
dial-peer voice 44 pots
preference 1
destination-pattern *8T
port 3/0/0
!
dial-peer voice 55 pots
preference 2
destination-pattern *4T
!
dial-peer voice 54 pots
preference 1
destination-pattern *4T
port 3/1/0
!
dial-peer voice 95 pots
preference 2
destination-pattern *6T
!
dial-peer voice 94 pots
preference 1
destination-pattern *6T
port 1/1/1
!
dial-peer voice 5555 voip
destination-pattern *9T
session protocol sipv2
session target ipv4:10.10.14.11
session transport tcp
!
num-exp 8025053... ...
gateway
timer receive-rtp 1200
!
sip-ua
authentication username 123456 password 256487675C
registrar ipv4:10.10.14.11 expires 3600
sip-server ipv4:x.x.x.x
!
!
gatekeeper
shutdown
!
banner motd ^C
!!!AUTHORIZED ACCESS ONLY !!!
Hostname : OH-RTR2.
Location : OH/BLR/IN/
Contact :IS Helpdesk
!!! AUTHORIZED ACCESS ONLY !!!
^C
!
line con 0
transport output all
line aux 0
transport preferred none
transport output none
line vty 0 5
password 7 1511021F0725
login
transport input all
transport output all
!
ntp clock-period 17180604
ntp server 10.10.8.1
!
end
Thanks
Roopesh
06-30-2012 07:34 AM
Who is your SIP provider?
Config may vary based primarily on whether they need authentication or not.
Have you searched this forum for examples as similar question was posted many times before.
SIP and H323 can coexist on the same router but SIP requires CUBE licenses when integrating to SIP provider.
Chris
Sent from Cisco Technical Support iPhone App
07-01-2012 11:16 PM
Hi chris,
Thanks for the Replay.
Our SIP provider is TATA Communications. They have Given the User ID and Password also SIP Proxy address.
We need help in configuration whether we need to configure the authentication in our Getaway(Router) or in CCM.
Please suggest.
Thanks
Roopesh
07-02-2012 05:58 AM
Authentication can only be done on CUBE as CUCM does not support authentication of SIP trunks (one of many benefits of having CUBE). So, you configure SIP trunk between CUBE and CUCM that is not authenticated and CUBE and service provider that configures authentication, you can either define the credentials on dial-peers or under sip-ua.
HTH,
Chris
05-16-2019 01:22 AM
TATA provider normally accept this format:
sip-ua
credentials number XXXXXXX username XXXXXXX password XXXXXXXX realm X.X.X.X(proxy-server IP)
authentication username XXXXXXX password XXXXXXXX
registrar ipv4:X.X.X.X expires 3600
sip-server ipv4:X.X.X.X
02-15-2021 04:23 AM
I have similar setup, but i want to know wether logical partitioning is required for such scenario.
Below is my setup.
Do i need to Deploy Logical Partition on ISR 4321 (India) or CUCM which is located in INDIA.
Hello,
I have a CUCM Cluster (Pub & Sub) , UCCX cluster (HA Mode) & 1 Voice gateways ISR 4321 (All at one location)
We have one PRI terminated, on a Voice Gateway (ISR 4321).
Configured SIP for PRI PSTN call routing between CUBE and CUCM.
IP Phones are for contact centre agents. (All users are using CIPC via VPN and located anywhere across the globe.)
We have one SIP Trunk from ITSP for ISD calling, which is terminated on the same ISR 4321 router.
So now my question is can we configure Logical Partitioning to avoid Toll Fraud between SIP Trunk and PRI.
Please note that SIP Trunk and PRI both are terminated on same route
02-15-2021 05:11 AM
You mentioned that the CC agents are located anywhere across the globe. Do they have a DID number to reach them or how the external users will be dialing into the Contact center ?
02-15-2021 06:38 AM
The agents are located I mean they are using CIPC over vpn from their laptop.
02-15-2021 06:39 AM
Means they can be in any part of the world.
02-15-2021 08:39 AM
Ok. Can the agents make outbound calls ? If they can, how is that call routed out ?
If you have Local Gateways in each country for routing outbound calls, then definitely you need to configure Logical partitioning. However if you only have Gateway in India and any outbound calls made by remote agents (logging in via VPN globally) are routed only via this gateway or agents wont make any external call, then there is no need for Logical partitioning config.
HTH
Rajan
Please rate all useful posts by clicking the star below and mark solutions as accepted wherever applicable
02-19-2021 03:12 AM
this setup has ITSP SIP trunks and E1 trunks.
02-19-2021 05:34 AM
Got it. As I mentioned where you have these. If you have these in India gateway and any external calls from any agents registering via VPN goes through this alone, then there is no need for logical partitioning config.
HTH
Rajan
please rate all useful posts by clicking the star below
02-19-2021 09:44 PM
Setup is in india itself.
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide