01-27-2011 12:41 PM - edited 03-16-2019 03:07 AM
hello
I have a Cisco 2620 router with a nm-hdv module fitted with vic-2mft-e1 card and 3 pvdm12 modules. Which I use for training and testing. I am trying to configure hardware transcoding and conference bridging.
I have a feature set that supports H.323 as I have the device configured as an H.323 gateway and this works with Call Manager 4.2(3) fine.
Trawling google, cco and this forum I need to enable dspfarm but prior to this on an NM-HDV module you have to issue the dsp services dspfarm card under the voice-card.
This command doesn't exists under my voice card
p1r3(config-voicecard)#?
Voice-card configuration commands:
codec Manage codec configuration parameters for voice card
default Set a command to its defaults
exit Exit from voice card configuration mode
no Negate a command or set its defaults
I have checked the command reference and the command was introduced in 12.2 so I am struggling to understand why this command is missing.
I have included the output from the show diag command
Slot 1:
High Density Voice Port adapter
Port adapter is analyzed
Port adapter insertion time unknown
EEPROM contents at hardware discovery:
Hardware Revision : 1.1
Top Assy. Part Number : 800-03567-01
Board Revision : F1
Deviation Number : 0-0
Fab Version : 02
PCB Serial Number : JAB04520CYT
RMA Test History : 00
RMA Number : 0-0-0-0
RMA History : 00
Product (FRU) Number : NM-HDV=
EEPROM format version 4
EEPROM contents (hex):
0x00: 04 FF 40 00 CC 41 01 01 C0 46 03 20 00 0D EF 01
0x10: 42 46 31 80 00 00 00 00 02 02 C1 8B 4A 41 42 30
0x20: 34 35 32 30 43 59 54 03 00 81 00 00 00 00 04 00
0x30: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
0x40: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
0x50: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
0x60: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
0x70: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
HDV SIMMs: Product (FRU) Number: PVDM-12
SIMM slot 0: Empty.
SIMM slot 1: Empty.
SIMM slot 2: PVDM-12 SIMM present.
SIMM slot 3: PVDM-12 SIMM present.
SIMM slot 4: PVDM-12 SIMM present.
VIC Slot 0:
E1 (2 Port) Multi-Flex Trunk WAN Daughter Card
Hardware revision 1.0 Board revision D0
Serial number 33106754 Part number 800-04479-03
Test history 0x0 RMA number 00-00-00
Connector type PCI
EEPROM format version 1
EEPROM contents (hex):
0x20: 01 23 01 00 01 F9 2B 42 50 11 7F 03 00 00 00 00
0x30: 68 00 00 00 05 02 12 00 FF FF FF FF FF FF FF FF
HDV firmware: Compiled Fri 19-Nov-04 14:23 by michen
HDV memory size 524280 heap free 167869
As always any help greatly appreciated.
01-28-2011 01:10 AM
Hey,
"show voice dsp" to check the status of the dsp channels.
Give this a try too:
give "sccp" command in global config mode
no dspfarm in global config mode
enable "debug dspfarm all"
in global config mode : "dspfarm"
then try configuring again
01-28-2011 12:27 PM
Thank you for your prompt response. None of the commands are available. However I have now discovered that the conferencing and transcoding is only available in the IP Plus Feature which will require a memory upgrade on my router to support.
Once again thank you
01-28-2011 12:53 PM
good to hear russell that u were able to figure out what was casuing the issue. btw could you post the output of show version to know which version ur using and your memory .. it would be informational..thnks
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide