NIM-2BRI-ST and ISR 4321

[Gilbert LECHA]

Hello ,

I have an ISR 4321 with 1 NIM-4FXSP and 1 NIM-2BRI S/T

when i take a show inventory, the nim subslot are good

Router#show inventory
NAME: "NIM subslot 0/1", DESCR: "NIM-4FXSP Voice Analog Module"
PID: NIM-4FXSP         , VID: V01  , SN: FOC22326BGM
NAME: "NIM subslot 0/2", DESCR: "NIM-2BRI-S/T DATA BRI Module"
PID: NIM-2BRI-S/T      , VID: V01  , SN: FOC221551VP
NAME: "PVDM subslot 0/4", DESCR: "PVDM4-32 Voice DSP Module"
PID: PVDM4-32          , VID: V02  , SN: FOC22318KXF

 When i take a Show platform , it's good also

Router#show platform diag
Chassis type: ISR4321/K9
Slot: 0, ISR4321/K9
  Running state               : ok
  Internal state              : online
  Internal operational state  : ok
  Physical insert detect time : 00:00:50 (00:03:40 ago)
  Software declared up time   : 00:01:50 (00:02:40 ago)
  CPLD version                : 17100927
  Firmware version            : 16.7(3r)
Sub-slot: 0/0, ISR4321-2x1GE
  Operational status          : ok
  Internal state              : inserted
  Physical insert detect time : 00:03:23 (00:01:08 ago)
  Logical insert detect time  : 00:03:23 (00:01:08 ago)
Sub-slot: 0/1, NIM-4FXSP
  Operational status          : ok
  Internal state              : inserted
  Physical insert detect time : 00:03:23 (00:01:07 ago)
  Logical insert detect time  : 00:03:23 (00:01:07 ago)
Sub-slot: 0/2, NIM-2BRI-S/T
  Operational status          : ok
  Internal state              : inserted
  Physical insert detect time : 00:03:23 (00:01:07 ago)
  Logical insert detect time  : 00:03:23 (00:01:07 ago)

 

 But when il wan't assign it to a dial-peer , i cannot assign the subslot 0/2

Router(config-dial-peer)#port 0/?
  <1-1>  Voice interface SubUnit #

Has someone already had this problem ?

Thank for your help

Gilbert

[R0g22]

"sh run | s interface" please.

[Gilbert LECHA]

Hi Nipun,

thank you for your interest in my problem

The sh run  is correct for interface BRI

interface BRI0/2/0:0
 description *** TO_de_secour ***
 no ip address
 encapsulation hdlc
 isdn switch-type basic-net3
 isdn timer T310 6000
 isdn point-to-point-setup
 isdn incoming-voice voice
!
interface BRI0/2/1:0
 description *** TO_de_secour ***
 no ip address
 encapsulation hdlc
 isdn switch-type basic-net3
 isdn timer T310 6000
 isdn point-to-point-setup
 isdn incoming-voice voice

But i don't see the voice card 0/2

voice-card 0/1
 no watchdog
!
voice-card 0/4
 no watchdog

[bichacko]

Hi,

What IOS version are you on?

I believe for NIM-2BRI-S/T, you need to be on 16.6.1 or above.

Do you have any other ISR4ks with this NIM card working?

Bijo

[Gilbert LECHA · Accepted solution]

Hi,

Yes we checked this, we are in 16.6.3
By cons we found where the problem comes from.
In fact, the gateway was not delivered with the correct card, we received a NIM-2BRI-S/T instead of a NIM-2BRI-NT/TE.
S/T only managing the data

Thank you all for the attention and the time you have devoted to solving my problem.

Regards