No option to configure VoIP dial-peer???

[ashok.cisco]

Hi all,

I have seen a very weird problem with a 2811 Voice GW.

I am not able to configure VoIP dial-peer. It's giving just POTS options like below.

DHL-VG-TH(config)#dial-peer voice 1 ?

  pots  Telephony

  <cr>

DHL-VG-TH(config)#dial-peer voice 1

I have attached the configurations and running on Voice IOS.

c2800nm-ipvoice-mz.124-4.t1.bin

Any advice?

Regards...

Ashok.

[acampbell]

Hi,

Can you post

show diag

Regards

Alex

[ashok.cisco]

Hi Alex,

Please find below....

VG-TH#sh diag

Slot 0:

        C2811 Motherboard with 2FE and integrated VPN Port adapter, 2 ports

        Port adapter is analyzed

        Port adapter insertion time unknown

        EEPROM contents at hardware discovery:

        PCB Serial Number        : FOC10484PVK

        Hardware Revision        : 1.0

        Top Assy. Part Number    : 800-26920-03

        Board Revision           : A0

        Deviation Number         : 0

        Fab Version              : 03

        RMA Test History         : 00

        RMA Number               : 0-0-0-0

        RMA History              : 00

        Processor type           : 87

        Hardware date code       : 20061205

        Chassis Serial Number    : FHK1050F2BC

        Chassis MAC Address      : 001a.6d05.8b58

        MAC Address block size   : 24

        CLEI Code                : COM7C00ARA

        Product (FRU) Number     : CISCO2811

        Part Number              : 73-10258-04

        Version Identifier       : V04

        EEPROM format version 4

        EEPROM contents (hex):

          0x00: 04 FF C1 8B 46 4F 43 31 30 34 38 34 50 56 4B 40

          0x10: 03 E7 41 01 00 C0 46 03 20 00 69 28 03 42 41 30

          0x20: 88 00 00 00 00 02 03 03 00 81 00 00 00 00 04 00

          0x30: 09 87 83 01 32 1C 15 C2 8B 46 48 4B 31 30 35 30

          0x40: 46 32 42 43 C3 06 00 1A 6D 05 8B 58 43 00 18 C6

          0x50: 8A 43 4F 4D 37 43 30 30 41 52 41 CB 8F 43 49 53

          0x60: 43 4F 32 38 31 31 20 20 20 20 20 20 82 49 28 12

          0x70: 04 89 56 30 34 20 D9 02 40 C1 FF FF FF FF FF FF

        WIC Slot 0:

        Serial 2T (12in1)

        Hardware revision 1.0           Board revision D0

        Serial number     24049180      Part number    800-03181-01

        FRU Part Number   WIC-2T=

        Test history      0x0           RMA number     00-00-00

        Connector type    PCI

        EEPROM format version 1

        EEPROM contents (hex):

          0x20: 01 12 01 00 01 6E F6 1C 50 0C 6D 01 00 00 00 00

          0x30: 68 00 00 00 00 10 12 00 FF FF FF FF FF FF FF FF

        WIC Slot 2:

        2nd generation - FXS Voice daughter card (2 port)

        Hardware Revision        : 3.1

        Top Assy. Part Number    : 800-21341-02

        Board Revision           : B0

        Deviation Number         : 0-0

        Fab Version              : 01

        PCB Serial Number        : FOC111930T6

        RMA Test History         : 00

        RMA Number               : 0-0-0-0

        RMA History              : 00

        Product (FRU) Number     : VIC2-2FXS

        Version Identifier       : V01

        CLEI Code                : CNUIAPPAAA

        EEPROM format version 4

        EEPROM contents (hex):

          0x00: 04 FF 40 00 47 41 03 01 C0 46 03 20 00 53 5D 02

          0x10: 42 42 30 80 00 00 00 00 02 01 C1 8B 46 4F 43 31

          0x20: 31 31 39 33 30 54 36 03 00 81 00 00 00 00 04 00

          0x30: CB 89 56 49 43 32 2D 32 46 58 53 89 56 30 31 20

          0x40: C6 8A 43 4E 55 49 41 50 50 41 41 41 FF FF FF FF

          0x50: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF

          0x60: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF

          0x70: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF

VG-TH#

Regards...

Ashok.

[acampbell]

Hi,

Your diags shows that there is a lack of any DSP chips

Without the DSP you can not use VOIP

For 2 FXS ports you need a min of PVDM2-8

HTH

Alex

Please rate useful posts

[ashok.cisco]

Hi Alex,

Ok.

But, I have other Voice GW with E1 card in it but no PVDMs. It's giving VoIP option.

VG-SG#sh diag

Slot 0:

        C2811 Motherboard with 2FE and integrated VPN Port adapter, 2 ports

        Port adapter is analyzed

        Port adapter insertion time 5d01h ago

        EEPROM contents at hardware discovery:

        PCB Serial Number        : FOC1206028B

        Hardware Revision        : 1.0

        Top Assy. Part Number    : 800-26920-04

        Board Revision           : A0

        Deviation Number         : 0

        Fab Version              : 04

        RMA Test History         : 00

        RMA Number               : 0-0-0-0

        RMA History              : 00

        Processor type           : 87

        Hardware date code       : 20080202

        Chassis Serial Number    : FHK1207F3DZ

        Chassis MAC Address      : 001f.6c6f.7830

        MAC Address block size   : 24

        CLEI Code                : COM7R00ARA

        Product (FRU) Number     : CISCO2811

        Part Number              : 73-10258-05

        Version Identifier       : V05

        EEPROM format version 4

        EEPROM contents (hex):

          0x00: 04 FF C1 8B 46 4F 43 31 32 30 36 30 32 38 42 40

          0x10: 03 E7 41 01 00 C0 46 03 20 00 69 28 04 42 41 30

          0x20: 88 00 00 00 00 02 04 03 00 81 00 00 00 00 04 00

          0x30: 09 87 83 01 32 66 4A C2 8B 46 48 4B 31 32 30 37

          0x40: 46 33 44 5A C3 06 00 1F 6C 6F 78 30 43 00 18 C6

          0x50: 8A 43 4F 4D 37 52 30 30 41 52 41 CB 8F 43 49 53

          0x60: 43 4F 32 38 31 31 20 20 20 20 20 20 82 49 28 12

          0x70: 05 89 56 30 35 20 D9 02 40 C1 FF FF FF FF FF FF

        WIC Slot 0:

        VWIC2-1MFT-T1/E1 - 1-Port RJ-48 Multiflex Trunk - T1/E1

        Hardware Revision        : 0.0

        Top Assy. Part Number    : 800-22628-05

        Board Revision           : B0

        Deviation Number         : 0

        Fab Version              : 04

        PCB Serial Number        : FOC12294W2D

        RMA Test History         : 00

        RMA Number               : 0-0-0-0

        RMA History              : 00

        Product (FRU) Number     : VWIC2-1MFT-T1/E1

        Version Identifier       : V01

        EEPROM format version 4

        EEPROM contents (hex):

          0x00: 04 FF 40 03 FD 41 00 00 C0 46 03 20 00 58 64 05

          0x10: 42 42 30 88 00 00 00 00 02 04 C1 8B 46 4F 43 31

          0x20: 32 32 39 34 57 32 44 03 00 81 00 00 00 00 04 00

          0x30: CB 90 56 57 49 43 32 2D 31 4D 46 54 2D 54 31 2F

          0x40: 45 31 89 56 30 31 20 D9 02 40 C1 FF FF FF FF FF

          0x50: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF

          0x60: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF

          0x70: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF

DHL-VG-SG#sh diag  | in PVDM

DHL-VG-SG#sh diag

Slot 0:

        C2811 Motherboard with 2FE and integrated VPN Port adapter, 2 ports

        Port adapter is analyzed

        Port adapter insertion time 5d01h ago

        EEPROM contents at hardware discovery:

        PCB Serial Number        : FOC1206028B

        Hardware Revision        : 1.0

        Top Assy. Part Number    : 800-26920-04

        Board Revision           : A0

        Deviation Number         : 0

        Fab Version              : 04

        RMA Test History         : 00

        RMA Number               : 0-0-0-0

        RMA History              : 00

        Processor type           : 87

        Hardware date code       : 20080202

        Chassis Serial Number    : FHK1207F3DZ

        Chassis MAC Address      : 001f.6c6f.7830

        MAC Address block size   : 24

        CLEI Code                : COM7R00ARA

        Product (FRU) Number     : CISCO2811

        Part Number              : 73-10258-05

        Version Identifier       : V05

        EEPROM format version 4

        EEPROM contents (hex):

          0x00: 04 FF C1 8B 46 4F 43 31 32 30 36 30 32 38 42 40

          0x10: 03 E7 41 01 00 C0 46 03 20 00 69 28 04 42 41 30

          0x20: 88 00 00 00 00 02 04 03 00 81 00 00 00 00 04 00

          0x30: 09 87 83 01 32 66 4A C2 8B 46 48 4B 31 32 30 37

          0x40: 46 33 44 5A C3 06 00 1F 6C 6F 78 30 43 00 18 C6

          0x50: 8A 43 4F 4D 37 52 30 30 41 52 41 CB 8F 43 49 53

          0x60: 43 4F 32 38 31 31 20 20 20 20 20 20 82 49 28 12

          0x70: 05 89 56 30 35 20 D9 02 40 C1 FF FF FF FF FF FF

        WIC Slot 0:

        VWIC2-1MFT-T1/E1 - 1-Port RJ-48 Multiflex Trunk - T1/E1

        Hardware Revision        : 0.0

        Top Assy. Part Number    : 800-22628-05

        Board Revision           : B0

        Deviation Number         : 0

        Fab Version              : 04

        PCB Serial Number        : FOC12294W2D

        RMA Test History         : 00

        RMA Number               : 0-0-0-0

        RMA History              : 00

        Product (FRU) Number     : VWIC2-1MFT-T1/E1

        Version Identifier       : V01

        EEPROM format version 4

        EEPROM contents (hex):

          0x00: 04 FF 40 03 FD 41 00 00 C0 46 03 20 00 58 64 05

          0x10: 42 42 30 88 00 00 00 00 02 04 C1 8B 46 4F 43 31

          0x20: 32 32 39 34 57 32 44 03 00 81 00 00 00 00 04 00

          0x30: CB 90 56 57 49 43 32 2D 31 4D 46 54 2D 54 31 2F

          0x40: 45 31 89 56 30 31 20 D9 02 40 C1 FF FF FF FF FF

          0x50: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF

          0x60: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF

          0x70: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF

VG-SG#

VG-SG(config)#dial-peer voice 1 ?

  mmoip  Multi Media Over IP

  pots   Telephony

  voatm  Voice over ATM

  vofr   Voice over Frame Relay

  voip   Voice over IP

VG-SG(config)#dial-peer voice 1

[acampbell]

Hi,

This is probably due to the IOS versions

Your 2811 is using 12.4.4T1  this has been retired by Cisco.

Not sure abot your other gateway.

Still think you need the DSP for VOIP working

Regards

Alex

[kgroves42 · Accepted solution]

You have a Dial-peer 1 already

     dial-peer voice 1 pots

once a dial-peer is added as pots or voip you can not change it.

You will have to remove it or use another dial-peer number such as 10

Thanks

[ashok.cisco]

Hi Kgroves,

Excellent observation.

Yes, that's the issue. Thanks a lot

Regards...

Ashok.