cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
613
Views
0
Helpful
5
Replies

Problem with sessions in Dspfarm profile

Not applicable

I have a problem with the Maximum sessions in DSPFARM Profile.

voice-card 0/1

 dsp services dspfarm

 no watchdog

---------------------------------------------------------------------------------------------

dspfarm profile 2 transcode

 description CISCO IOS Enhanced Media Termination Point

 codec g729abr8

 codec g729ar8

 codec g711alaw

 codec g711ulaw

 codec g729r8

 codec g729br8

 codec gsmamr-nb

 maximum sessions 1   // I can't choise another option.

 associate application SCCP

-----------------------------------------------------------------------------------

dspfarm profile 1 conference

 description CISCO IOS Enhanced Conference Bridge

 codec g729br8

 codec g729r8

 codec g729abr8

 codec g729ar8

 codec g711alaw

 codec g711ulaw

 codec ilbc

associate application SCCP

...........................maximum sessions 0   // I can't choise another option.

 

#show inv


NAME: "Chassis", DESCR: "Cisco ISR4321 Chassis"
PID: ISR4321/K9        , VID: V04, SN: FLM2123V1NN

NAME: "Power Supply Module 0", DESCR: "110W AC Power Supply for Cisco ISR 4320"
PID: PWR-4320-AC       , VID:    , SN:

NAME: "Fan Tray", DESCR: "Cisco ISR4320 Fan Assembly"
PID: ACS-4320-FANASSY  , VID:    , SN:

NAME: "module 0", DESCR: "Cisco ISR4321 Built-In NIM controller"
PID: ISR4321/K9        , VID:    , SN:

NAME: "NIM subslot 0/1", DESCR: "NIM-1MFT-T1/E1 - T1/E1 Serial Module"
PID: NIM-1MFT-T1/E1    , VID: V04, SN: FOC211936CP

NAME: "subslot 0/1 db module 0", DESCR: "PVDM4-32 Voice DSP Module"
PID: PVDM4-32          , VID: V02, SN: FOC21195J2V

NAME: "NIM subslot 0/2", DESCR: "NIM-2FXO Voice Analog Module"
PID: NIM-2FXO          , VID: V01, SN: FOC204407WW

NAME: "NIM subslot 0/0", DESCR: "Front Panel 2 ports Gigabitethernet Module"
PID: ISR4321-2x1GE     , VID: V01, SN: JAB092709EL

NAME: "module R0", DESCR: "Cisco ISR4321 Route Processor"
PID: ISR4321/K9        , VID: V04, SN: FDO21131A6X

NAME: "module F0", DESCR: "Cisco ISR4321 Forwarding Processor"
PID: ISR4321/K9        , VID:    , SN:

What should I do?

5 Replies 5

Jaime Valencia
Cisco Employee
Cisco Employee

You only have a 32 channel PVDM, and assuming that you already configured that T1, you do not have any more resources, you need to buy and install another PVDM module.

HTH

java

if this helps, please rate

Thanks Jaime for your answer, but can I configure with 16 channels the E1 for to have more resources?

Yes, assuming you're receiving a partial PRI from your telco, but with just 16 channels, and using high complexity codecs, you'll get very few sessions with those resources.

HTH

java

if this helps, please rate

I understand, then the configuration of E1 would be:

controller E1 0/1/0

 pri-group timeslots 1-15 service mgcp

FYI, we do not support partial PRI with MGCP, you can configure it, but you won't have Cisco support if you need assistance with any problem you face.

That's only supported with H.323

HTH

java

if this helps, please rate