SIP Trunk to Broadsoft

[Juan Pablo Hidalgo Villacres]

Hi,

i am new at Cisco IP Telephony. I have a 2921 CME 9.1.

I would like to configure a SIP Trunk to Broadsoft, but i don't know where i could find information for doing this?.. what do i need to configure?..

i have created a SIP Trunk to another CME without problem, this works great, and i have replicated that sip trunk config trying to create the sip trunk to broadsoft but it didn't work..

Hope somebody give the clues for this,

regards

[Anas Abueideh]

Hi Juan,

is you provider required credentials. you need the following config

voice service voip

allow-connections h323 to h323

allow-connections h323 to sip

allow-connections sip to h323

allow-connections sip to sip

fax protocol cisco

sip

  bind control source-interface Loopback

  bind media source-interface Loopback

sip-ua

credentials username xxxxxxxxxxx password 7

xxxxxxxxxxx realm sip.voip-unlimited.net

credentials username

xxxxxxxxxxx

password 7

xxxxxxxxxxx

realm sip.voip-unlimited.net

authentication username xxxxxxxxx password 7 xxxxxxxxx realm xxx.xxxxxxx.xxx

calling-info pstn-to-sip from number set xxxxxxxxxx

retry register 10

timers register 1000

mwi-server ipv4:192.168.0.159 expires 3600 port 5060 transport udp unsolicited

registrar

xxx.xxxxxxx.xxx

expires 60

dial-peer voice 100 voip

    destination-pattern 9..........

    session protocol sipv2

    session target ipv4:x.x.x.x -- Your SIP provider IP

    dtmf-relay rtp-nte

    codec g711alaw

    no vad

!

also find the below links

https://supportforums.cisco.com/message/3710223#3710223

https://supportforums.cisco.com/message/3305556#3305556

https://supportforums.cisco.com/message/3646952#3646952

HTH

Anas

please don't forget to rate the helpful posts

[Juan Pablo Hidalgo Villacres]

Hi Anas,

thanks for your reply,

no, my service provider doesn't need credentials,

I have configured the dial-peer and voice service voip,

The sip-au is for credentials, is that correct?., so i think my configuration is ok..

regards,

[Ayodeji Okanlawon]

Juan,

We use Broadsoft so I may be able to help. What is not working? Did broadsoft team provide you with the ip address to use and the port number to connect to. Broadsoft most times do not use the default port 5060.  Do you have all your details correct?

Can you send your config, a description of whats failing and we can then take it from there...We may need to look at logs too

Please rate all useful posts

"opportunity is a haughty goddess who waste no time with those who are unprepared"

[Anas Abueideh]

the sip-ua for credentials

HTH

Anas

please don't forget to rate the helpful posts

[Ayodeji Okanlawon]

Anas, broadsoft doesnt use sip-ua credentials to authenticate...

Please rate all useful posts

"opportunity is a haughty goddess who waste no time with those who are unprepared"

[Juan Pablo Hidalgo Villacres]

Hi,

thanks for your replies,

the provider is reviewing his configuration, i think they forgot something..

i'll wait for a couple of minutes to see if they have fixed the config.. maybe the problem is not mine..

Thanks for your help,

i have this debugs output (debug ccsip all)...

regards,

[Juan Pablo Hidalgo Villacres]

sorry i forgot the configuration..

voice service voip

allow-connections h323 to h323

allow-connections h323 to sip

allow-connections sip to h323

allow-connections sip to sip

no supplementary-service sip handle-replaces

fax protocol t38 version 0 ls-redundancy 0 hs-redundancy 0 fallback none

sip

  registrar server

dial-peer voice 104 voip

destination-pattern 1...

session protocol sipv2

session target ipv4:10.1.105.20

dtmf-relay rtp-nte

codec g711ulaw

i think you only need this,

regards

[Ayodeji Okanlawon]

What is your setup like...Broadsoft ip is 10.1.105.20...What Ip do you reach broadsoft on..You are orginating invite from 172.16.163.2...

Please describe your full setup..

Please rate all useful posts

"opportunity is a haughty goddess who waste no time with those who are unprepared"

[Juan Pablo Hidalgo Villacres]

sorry for not mention that,

yes my cme IP is 172.16.163.2, and broadsoft is 10.1.105.20, it is a dedicated link.. i can ping 10.1.105.20 from the CME...

broadsoft is used on my company but at another country,, so we have a dedicated link for the connection..

if you need something else please let me know,

regards,

[Ayodeji Okanlawon]

Can you send your full show run please. The question is what is the ip on your CCME that connects to 10.1.105.20..It cant be 172.16..

Please rate all useful posts

"opportunity is a haughty goddess who waste no time with those who are unprepared"

[Juan Pablo Hidalgo Villacres]

this is the sh run,

yes the IP that connects to broadsoft is 172.16.163.2,

as i said the connection is through a private dedicated link,

regards,

[Ayodeji Okanlawon · Accepted solution]

Ok,

Everything looks okay..You are getting 604 from broadsoft..Looks like they are unable to route the dialled number,,,

Received:

SIP/2.0 604 Does not exist anywhere

Via:SIP/2.0/UDP 172.16.163.2:5060;branch=z9hG4bK5EF18C2

From:"Juan Pablo Hidalgo"<4901>;tag=60B3BF88-382

To:<1868>;tag=819031417-1365024129334

Call-ID:646DABB7-9BDB11E2-872E92A8-E092A3AB@172.16.163.2

CSeq:101 INVITE

Content-Length:0

Received:

Please rate all useful posts

"opportunity is a haughty goddess who waste no time with those who are unprepared"

[Juan Pablo Hidalgo Villacres]

Thanks for your help,

i have to wait for them to configure it correctly,

regards,