Time Synchronization issue on CUCM with NTP Server (Cisco Router) - Page 2

jahanzaib amin · ‎11-30-2013

Hello Experts,

We need your suggestion to configure Cisco 3800 Router as NTP Server and Syn with Cisco Call Manager to show correct time order on Cisco IP Phones.

There was a NTP Server before which is remove now but IP Phones are showing 30 min off from the Actual time.

We did Cisco 3800 as NTP server and added in CUCM as NTP Server but still time is showing different on Cisco IP Phones.

Please assist.

Thanks,

jahanzaib amin · ‎12-02-2013

Hello,

CUCM Version: 6.1 and IP Phones are:

Cisco 7940
Cisco 7941
Cisco 7942
Cisco 7970
Cisco 7971
Cisco 7975
Cisco 7906
Cisco 7937

Further the Day/Time group we will reset in O/S mode? in Line Properties?

Aman Soi · ‎12-02-2013

Hi Amin,

diagnostic test shows NTP is failed.

test - ntp_stratum : Failed

The reference NTP server is a stratum 12 clock.

NTP servers with startum 5 or worse clocks are deemed unreliable.

Please consider using an NTP server with better startum level.

do u have any other NTP server in setup ?

regds,

aman

jahanzaib amin · ‎12-02-2013

Hello Aman,

We dont have other server. We configure Cisco router as NTP Server. Please see the config below:

VG-Router#sh run | s ntp

ntp source GigabitEthernet0/0

ntp master 1

ntp update-calendar

----------------------------------------------------------------

VG-Router#sh clo

VG-Router#sh clock

11:46:32.603 GMT+3 Thu Nov 28 2013

How we can define different startum level on CUCM?

Aman Soi · ‎12-02-2013

Hi Amin,

Just try entering the command ntp master and check show ntp associations detail.

http://www.freeccnaworkbook.com/workbooks/ccna/configuring-the-cisco-ios-ntp-server

regds,

aman

jahanzaib amin · ‎12-02-2013

Hello Aman,

Greate This I already define on Cisco Gateway.

VG-Router#sh run | s ntp

ntp source GigabitEthernet0/0

ntp master 1

ntp update-calendar

Further we need to match Stratum with CM so either we update the Stratum on CM to match with NTP Server (router)

or either on NTP Server (Router).

What will be best praticse to update on router or CM?

Thanks,

Aman Soi · ‎12-02-2013

Hi Amin,

I do not think there is any way to change stratum on Cisco Call manager.

can u share show ntp associations detail on router ?

you can refer the link

https://supportforums.cisco.com/message/4059836#4059836

regds,

aman

Manish Prasad · ‎12-02-2013

Its pretty strange , i try to emulate same issue on lab with cucm 7 and cipc . its stuck. cipc time is not getting updated even after restarting node. its picking up time locally but not from cucm or ntp reference. are we missing something or is this some kind of bug?

-----------------------------------

admin:utils ntp status

ntpd (pid 12879) is running...

remote refid st t when poll reach delay offset jitter

==============================================================================

127.127.1.0 LOCAL(0) 10 l 15 64 3 0.000 0.000 0.001

*10.0.0.16 CHU_AUDIO(1) 2 u 14 64 3 17.315 7.488 8.891

synchronised to NTP server (10.0.0.16) at stratum 3

time correct to within 892 ms

polling server every 64 s

Current t i m e i n U T C i s : Mon Dec 2 01:07:21 UTC 2013

Current t i m e i n A s i a / K o l k a t a i s : Mon Dec 2 06:37:21 IST 2013

admin:

--------------------------------------------------------

Aman Soi · ‎12-02-2013

Hi Amin,

Just a thought :

NTP master clock not able to synchronize

CSCth87350

Description

Symptom:

NTP master clock not able to synchronize

Condition

issue is seen in 3845 routers.platfrom depended.

Workaround:

There is no known workaround

Known Affected Releases:

12.3(11)T8

what is the exact IOS version and model of 3800 series router u are using?

regds,

aman

jahanzaib amin · ‎12-03-2013

Hello Aman,

Here is out put for the NTP Associate on the Router. I am afraid that the IP showing in below output is not showing correct one.

------------------------------------------------

VG-router#show ntp associations

address ref clock st when poll reach delay offset disp

*~127.127.1.1 .LOCL. 0 11 16 377 0.000 0.000 0.232

* sys.peer, # selected, + candidate, - outlyer, x falseticker, ~ configured

I did below setting on the Cisco Router to become NTP Server.

VG-Router#sh run | s ntp

ntp source GigabitEthernet0/0

ntp master 1

ntp update-calendar

--------------------

VG-Router#sh clock

11:46:32.603 GMT+3 Thu Nov 28 2013

and ip for the inside Gigabit interface is 172.16.7.2 but the above output is not showing the IP in NTP Association.

Further the Model for Router is 3825 and IOS is :

" 2800 Software (C2800NM-ADVENTERPRISEK9_IVS_LI-M), Version 15.1(4)M5, RELEASE SOFTWARE (fc1)"

Thanks,

Jehan

Aman Soi · ‎12-03-2013

Hi Amin,

Could not understand why this is happening?

further , the model u are mentioning is 3825 but snapshot is for 2800.

regds,

aman

jahanzaib amin · ‎12-03-2013

Hi,

I have no idea that why the router is not showing correct detail in Sh NTP assocation command.

Router is not remote location i dont have direct access. I did show version to see the IOS. Which command can tell us the router model?

Aman Soi · ‎12-03-2013

Hi Amin,

u can use the show version,show inventory and show diag command .

what I suggest is open discussion in Router section?

regds,

aman

jahanzaib amin · ‎12-03-2013

Hello Aman,

Ok I will check with Routing Team.... But let assume if we make Call Manager as NTP server so IP Phones can

get the time from Call Manager it self. Than what are the core steps to configure it.

Let try to make Call manager as NTP Server. In below NTP Ref will give Call Manager Publisher IP Address?

Further Select here the NTP Reference.

Thanks,

Jehan

Aman Soi · ‎12-04-2013

Hi Amin,

I do not think u can make call manager as NTP server.

It can act as NTP client.If anybody has an idea, please let us know.

http://www.cisco.com/en/US/products/sw/voicesw/ps556/products_tech_note09186a008009470f.shtml

regds,

aman

jahanzaib amin · ‎12-04-2013

Hello Aman,

Ok...but is there any other way that IP Phones Syn with the Call Manager Clock? Becuase there is Clock setting on the Call Manager. So if the IP Phoens Syn with Call Manager Time Clock that its also fine and acceptable.

Thanks,

Jehan