cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
3105
Views
15
Helpful
8
Replies

VG-310

John Huthmaker
Level 4
Level 4

I've been asked to do some research in to installing a Cisco VG 310.  I wanted to see if anyone on the support forums have installed one before.  I did some poking around, and configured a mock one in my home lab.  It looks like its really just a basic voice gateway (router) with a ton of FXS ports.  It looks like its best to just set it up as an MGCP gateway, and then configure your ports as you would any other FXS port in CUCM.  Is that correct, or am I missing something?

2 Accepted Solutions

Accepted Solutions

Wilson Samuel
Level 7
Level 7

Hi John

As far as I know, the Supplementary Services are much better served with the SCCP in VG3XX or VG2XX GWs.

So, in essence, it will be best if you can configured the GW in SCCP mode

HTH

 

http://www.cisco.com/c/en/us/products/collateral/unified-communications/vg-series-gateways/product_data_sheet09186a00801d87f6.html

View solution in original post

Terry Cheema
VIP Alumni
VIP Alumni

Yes its got lot of fxs ports but it does support TDM and other protocols as well apart from MGCP, Refer:

http://www.cisco.com/c/en/us/products/collateral/unified-communications/vg-series-gateways/product_data_sheet09186a00801d87f6.html

Protocols Supported

The voice gateways support the following protocols:

   SCCP

   H.323v4

   MGCP

   SIP

   Real-Time Transport Protocol (RTP)

   Secure Real-Time Transport Protocol (SRTP)

   Trivial File Transfer Protocol (TFTP)

   HTTP server

   SNMP

   Telnet

   Dynamic Host Configuration Protocol (DHCP)

   Domain Name System (DNS)

   Cisco Unified Communications Manager or Cisco Unified Communications Manager Express redundancy support using Hot Standby Router Protocol (HSRP)

   Call survivability: MGCP failover to an H.323 connection to the SRST router

   Cisco Fax Relay, T.38 fax relay, and modem pass-through

   Coder/decoder (codec) support, G.711, and G.729a

   RADIUS and TACACS+ for Telnet and authorization

 

Also refer to technical specifications.

 

Also Refer here: http://www.cisco.com/c/en/us/td/docs/voice_ip_comm/cucm/admin/10_0_1/ccmsys/CUCM_BK_SE5FCFB6_00_cucm-system-guide-100/CUCM_BK_SE5FCFB6_00_cucm-system-guide-100_chapter_0100110.html#CUCM_RF_V83D221A_00

Cisco VG310

MGCP

T1/CAS/PRI

E1/PRI

FXS/FXO/BRI

 
 

SCCP

 

FXS/BRI

 
 

H.323 and SIP

T1/CAS/PRI

E1/PRI

FXS/FXO/BRI

 

 

Refer to this post as well someone asked this couple of days ago:

https://supportforums.cisco.com/discussion/12561676/using-vg310-voice-router-wpri

-Terry

Please rate all helpful posts

View solution in original post

8 Replies 8

Wilson Samuel
Level 7
Level 7

Hi John

As far as I know, the Supplementary Services are much better served with the SCCP in VG3XX or VG2XX GWs.

So, in essence, it will be best if you can configured the GW in SCCP mode

HTH

 

http://www.cisco.com/c/en/us/products/collateral/unified-communications/vg-series-gateways/product_data_sheet09186a00801d87f6.html

Wilson looks like we are replying to the questions at same time :)

-Terry

Ha ha, that was a nice co-incidence :-)

regards

Thanks for the help guys.  This is all good info.

Just wanted to follow up.  I installed the VG310 at a client site yesterday.  It was pretty seamless.  I did a "sho int g0/0" to get the mac address, and added it to CUCM with a SCCP integration. Once adding a couple commands at the interface, and adding the interface to CUCM it came right up.  It was much easier than I anticipated, and worked well.  I was able to get a 10 page fax in without any issue, and the client uses SIP trunks.

Glad that we were able to help

Regards

Good one John - thanks for the update! (+5)

-Terry

Please rate all helpful posts
 

Terry Cheema
VIP Alumni
VIP Alumni

Yes its got lot of fxs ports but it does support TDM and other protocols as well apart from MGCP, Refer:

http://www.cisco.com/c/en/us/products/collateral/unified-communications/vg-series-gateways/product_data_sheet09186a00801d87f6.html

Protocols Supported

The voice gateways support the following protocols:

   SCCP

   H.323v4

   MGCP

   SIP

   Real-Time Transport Protocol (RTP)

   Secure Real-Time Transport Protocol (SRTP)

   Trivial File Transfer Protocol (TFTP)

   HTTP server

   SNMP

   Telnet

   Dynamic Host Configuration Protocol (DHCP)

   Domain Name System (DNS)

   Cisco Unified Communications Manager or Cisco Unified Communications Manager Express redundancy support using Hot Standby Router Protocol (HSRP)

   Call survivability: MGCP failover to an H.323 connection to the SRST router

   Cisco Fax Relay, T.38 fax relay, and modem pass-through

   Coder/decoder (codec) support, G.711, and G.729a

   RADIUS and TACACS+ for Telnet and authorization

 

Also refer to technical specifications.

 

Also Refer here: http://www.cisco.com/c/en/us/td/docs/voice_ip_comm/cucm/admin/10_0_1/ccmsys/CUCM_BK_SE5FCFB6_00_cucm-system-guide-100/CUCM_BK_SE5FCFB6_00_cucm-system-guide-100_chapter_0100110.html#CUCM_RF_V83D221A_00

Cisco VG310

MGCP

T1/CAS/PRI

E1/PRI

FXS/FXO/BRI

 
 

SCCP

 

FXS/BRI

 
 

H.323 and SIP

T1/CAS/PRI

E1/PRI

FXS/FXO/BRI

 

 

Refer to this post as well someone asked this couple of days ago:

https://supportforums.cisco.com/discussion/12561676/using-vg310-voice-router-wpri

-Terry

Please rate all helpful posts

Getting Started

Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: