cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
1375
Views
0
Helpful
1
Replies
Julie Tupling
Beginner

ME3400E parent child policy map

I've pasted the output of the show policy-map that is applied to an interface that connected to an access layer switch - I want one customer to have 15MB and the other customers to share the remaining bandwidth of the 200MB of internet bandwidth we currently have.

Does it look like it is working?  It has only been applied for an hour or 2 - I dont' understand why under the Class-map:  cust1 is shows 0 packets, and under the service policy class-Map is shows 0 packets and 0 bytes, but it shows that packets are conforming under the police section . . .

ME.3400#sh policy-map int g0/11

GigabitEthernet0/11

  Service-policy input: IP_Parent

    Class-map: cust1 (match-any)

      0 packets

      Match: vlan  301

      Service-policy : cust1

Class-map: class-default (match-any)

          0 packets, 0 bytes

          5 minute offered rate 0 bps, drop rate 0 bps

          Match: any

      police cir 15000000 bc 468750

         conform-action transmit

         exceed-action drop

      conform: 3354685 (packets) 596174238 (bytes)

      exceed: 0 (packets) 0 (bytes)

      conform: 1945694 bps, exceed: 0 bps

    Class-map: Shared_IP (match-any)

      0 packets

      Match: vlan  300

      Service-policy : Shared_IP

        Class-map: class-default (match-any)

          0 packets, 0 bytes

          5 minute offered rate 0 bps, drop rate 0 bps

          Match: any

      police cir 80000000 bc 1000000

         conform-action transmit

         exceed-action drop

      conform: 878911 (packets) 145461269 (bytes)

      exceed: 0 (packets) 0 (bytes)

      conform: 409508 bps, exceed: 0 bps

    Class-map: class-default (match-any)

      0 packets, 0 bytes

      5 minute offered rate 0 bps, drop rate 0 bps

      Match: any

1 REPLY 1
Julie Tupling
Beginner

Here is the output after letting it run for 6 days.  Does anyone have an opinion about if it is working correctly?

I'm still confused by the places where it says 0 packets, or 0 packets, 0 bytes.

ME.3400#sh policy-map int g0/11

GigabitEthernet0/11

  Service-policy input: IP_Parent

    Class-map: cust1 (match-any)

      0 packets

      Match: vlan  301

      Service-policy : cust1

        Class-map: class-default (match-any)

          0 packets, 0 bytes

          5 minute offered rate 0 bps, drop rate 0 bps

          Match: any

      police cir 15000000 bc 468750

         conform-action transmit

         exceed-action drop

      conform: 911003596 (packets) 153048040973 (bytes)

      exceed: 445 (packets) 439435 (bytes)

      conform: 2501473 bps, exceed: 0 bps

    Class-map: Shared_IP (match-any)

      0 packets

      Match: vlan  300

      Service-policy : Shared_IP

        Class-map: class-default (match-any)

          0 packets, 0 bytes

          5 minute offered rate 0 bps, drop rate 0 bps

          Match: any

      police cir 180000000 bc 1000000

         conform-action transmit

         exceed-action drop

      conform: 262737871 (packets) 42238049347 (bytes)

      exceed: 0 (packets) 0 (bytes)

      conform: 1005000 bps, exceed: 0 bps

    Class-map: class-default (match-any)

      0 packets, 0 bytes

      5 minute offered rate 0 bps, drop rate 0 bps

      Match: any