08-20-2013 11:05 AM
Am having problem bringing up mpls l2vpn between asr9k and 7609 router . Below is my config. The interfaces are up, the vc working, but can't ping across.
AS9K
***********************************************************
interface GigabitEthernet0/2/0/6.609 l2transport
encapsulation dot1q 609
rewrite ingress tag pop 1 symmetric
mtu 1526
!
pw-class TST
encapsulation mpls
transport-mode vlan
!
xconnect group TST
p2p TST
interface GigabitEthernet0/6.609
neighbor 2.2.2.2 pw-id 609
pw-class TST
***************************************************************************
7609
***********************************************************************************
interface gig 3/4.609
encapsulation dot1q 609
xconnect 1.1.1.1 609 encapsulation mpls
***OUTPUT FROM ASR9K********
RP/0/RSP0/CPU0#sh l2vpn xconnect pw-class TST detail
Group X,X, state is up; Interworking none
AC: GigabitEthernet0/6.609, state is up
Type VLAN; Num Ranges: 1
VLAN ranges: [905, 905]
MTU 1512; XC ID 0x1040003; interworking none
Statistics:
packets: received 735789487, sent 725878036
bytes: received 405747931393, sent 184926449749
drops: illegal VLAN 0, illegal length 0
PW: neighbor 2.2.2.2, PW ID 609, state is up ( established )
PW class ENS, XC ID 0xc0000003
Encapsulation MPLS, protocol LDP
Source address 1.1.1.1
PW type Ethernet VLAN, control word disabled, interworking none
PW backup disable delay 0 sec
Sequencing not set
PW Status TLV in use
MPLS Local Remote
------------ ------------------------------ -----------------------------
Label 17442 847
Group ID 0x80003c0 0x0
Interface GigabitEthernet0/6.609 uknown
MTU 1512 1512
Control word disabled disabled
PW type Ethernet VLAN Ethernet VLAN
VCCV CV type 0x2 0x2
(LSP ping verification) (LSP ping verification)
VCCV CC type 0x6 0x6
(router alert label) (router alert label)
(TTL expiry) (TTL expiry)
------------ ------------------------------ -----------------------------
Incoming Status (PW Status TLV):
Status code: 0x0 (Up) in Notification message
Outgoing Status (PW Status TLV):
Status code: 0x0 (Up) in Notification message
MIB cpwVcIndex: 3221225475
Statistics:
packets: received 725878036, sent 735789487
bytes: received 184926449749, sent 405747931393
*******7609 OUTPUT*******
Local interface: Gi1/3.609 up, line protocol up, Eth VLAN 609 up
Destination address: 1.1.1.1, VC ID: 609, VC status: up
Output interface: Gi2/4, imposed label stack {0 151644}******************This is my problem no imposed label on 7609
Preferred path: not configured
Default path: active
Next hop: 10.198.64.21
Create time: 00:00:16, last status change time: 00:00:16
Signaling protocol: LDP, peer 1.1.1.1 up
Targeted Hello: 2.2.2.2(LDP Id) -> 1.1.1.1, LDP is UP
Status TLV support (local/remote) : enabled/supported
LDP route watch : enabled
Label/status state machine : established, LruRru
Last local dataplane status rcvd: No fault
Last local SSS circuit status rcvd: No fault
Last local SSS circuit status sent: No fault
Last local LDP TLV status sent: No fault
Last remote LDP TLV status rcvd: No fault
Last remote LDP ADJ status rcvd: No fault
MPLS VC labels: local 505, remote 151644
Group ID: local 0, remote 134218688
MTU: local 1508, remote 1508
Remote interface description: GigabitEthernet0_6_.609
Sequencing: receive disabled, send disabled
Control Word: Off (configured: autosense)
SSO Descriptor: 1.1.1.1/609, local label: 505
SSM segment/switch IDs: 57633/24673 (used), PWID: 28772
VC statistics:
transit packet totals: receive 3, send 0
transit byte totals: receive 216, send 0
transit packet drops: receive 0, seq error 0, send 0
08-20-2013 05:46 PM
Hi Ogungbenro,
Can you please post the output of a "show ip cef 1.1.1.1 int" from the 7609.
Regards
08-27-2013 11:32 AM
Hello ogungbenro wale,
Would you be so kind to verify the output form 7600, since the config part does not correspond to VC you provided output for:
interface gig 3/4.609 <=
...
Local interface: Gi1/3.609 up, line protocol up, Eth VLAN 609 up <=
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide