cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
883
Views
0
Helpful
6
Replies

"%SYS-2-QCOUNT: Bad deqeueue"

jresendizz
Level 1
Level 1

Hi guys, having a 7513 runing MPLS VPN, wiht QoS, the router started since 1 week ago with this log:

14w1d: %SYS-2-QCOUNT: Bad deqeueue 63C85E28 count 1

-Process= "<interrupt level>", ipl= 1

-Traceback= 6025FEC0 60260660 60261274 60261380

There is no affectation of traffic, but i would like to know if could hace a potential problem..

Thanx in advice, guys!

Kind Regards

6 Replies 6

It's a SW problem, but going to need to know what version and featureset of code you are running, could you please post a "sh ver" to the forum

Hi, gallagh, thanks for your answer, this is the sh ver of this equipment:

Router#sh ver

Cisco Internetwork Operating System Software

IOS (tm) RSP Software (RSP-JSV-M), Version 12.2(17a), RELEASE SOFTWARE (fc1)

Copyright (c) 1986-2003 by cisco Systems, Inc.

Compiled Thu 19-Jun-03 14:21 by pwade

Image text-base: 0x60010948, data-base: 0x61982000

ROM: System Bootstrap, Version 12.0(10r)S1, RELEASE SOFTWARE (fc1)

PE_Mty uptime is 14 weeks, 2 days, 3 hours, 2 minutes

System returned to ROM by bus error at PC 0x60DD0EB4, address 0xB0D0B75 at 09:56:08 CST6CDT Tue Jan 4 2000

System restarted at 13:06:07 CST6CDT Wed Jul 28 2004

System image file is "slot0:rsp-jsv-mz.122-17a.bin"

cisco RSP4+ (R5000) processor with 262144K/2072K bytes of memory.

R5000 CPU at 200Mhz, Implementation 35, Rev 2.1, 512KB L2 Cache

Last reset from power-on

G.703/E1 software, Version 1.0.

G.703/JT2 software, Version 1.0.

Channelized E1, Version 1.0.

X.25 software, Version 3.0.0.

SuperLAT software (copyright 1990 by Meridian Technology Corp).

Bridging software.

TN3270 Emulation software.

Primary Rate ISDN software, Version 1.1.

Chassis Interface.

1 VIP2 R5K controller (2 FastEthernet).

4 VIP4-50 RM5271 controllers (2 Serial)(24 E1)(1 ATM)(3 Channelized E3).

2 FastEthernet/IEEE 802.3 interface(s)

327 Serial network interface(s)

1 ATM network interface(s)

3 Channelized E3 port(s)

123K bytes of non-volatile configuration memory.

32768K bytes of Flash PCMCIA card at slot 0 (Sector size 128K).

16384K bytes of Flash internal SIMM (Sector size 256K).

Slave in slot 7 is running Cisco Internetwork Operating System Software

IOS (tm) RSP Software (RSP-DW-M), Version 12.2(17a), RELEASE SOFTWARE (fc1)

Copyright (c) 1986-2003 by cisco Systems, Inc.

Compiled Thu 19-Jun-03 14:28 by pwade

Slave: Loaded from system

Slave: cisco RSP4 (R5000) processor with 262144K bytes of memory.

Configuration register is 0x2102

It looks like you are hitting:

http://www.cisco.com/cgi-bin/Support/Bugtool/onebug.pl?bugid=CSCea72991&Submit=Search

It's fixed in 12.2(17.8)

HTH

Thanks for the answer!!

Cisco recommend us to make these Workarouds:

1.- Reset the VIP (we already did it but the error is appearing again)

2.- Microcode Reload...we haven´t done that because of the affectation (costumers)...

Gallagh i would like to know if you have or know about other workaround...the problem is because is now appearing on other Routers ...=(

Thank you very much for your help!!

Regards

These are the workaround from the bug release-note:

- when reconfiguring a channel-group, shut down the interface beforehand

- when reconfiguring a "service-policy" command applied directly to a physical interface, shut down the interface beforehand

- when reconfiguring a "service-policy" command applied to a Multilink interface, shut down the member interface(s) beforehand

- when reconfiguring a "service-policy" command applied to a Frame-relay map-class, remove the map-class from the interface beforehand

Otherwise you are going to have to upgrade to 12.2(19) or later.

Hello, gallag!

It seems is a "bad practice" it seems somebody has been attaching a EMPTY map-class within a subinterface; and after that is creating the map-class..

Thank you very much for your very helpful answer!!!