I believe the reason is that

gregwoodson · ‎06-16-2014

I have a Sup720-3B- it is using the same version of code as my other 6500 series switches that are supporting LDP/MPLS. Here is the sh mod:

Mod Ports Card Type Model Serial No.
--- ----- -------------------------------------- ------------------ -----------
1 24 CEF720 24 port 1000mb SFP WS-X6724-SFP SAD08290FLG
2 16 16 port 1000mb GBIC ethernet WS-X6416-GBIC SAD04240LDR
3 16 16 port 1000mb GBIC ethernet WS-X6416-GBIC SAD041406L9
4 48 48-port 10/100/1000 RJ45 EtherModule WS-X6148A-GE-TX SAL09507UST
5 2 Supervisor Engine 720 (Active) WS-SUP720-3B SAL1208GTEL

Mod MAC addresses Hw Fw Sw Status
--- ---------------------------------- ------ ------------ ------------ -------
1 0011.9210.1774 to 0011.9210.178b 2.1 12.2(18r)S1 12.2(33)SXI1 Ok
2 00d0.d3a4.c5dd to 00d0.d3a4.c5ec 1.1 5.3(1) 12.2(33)SXI1 Ok
3 0030.19d8.59c8 to 0030.19d8.59d7 1.1 5.3(1) 12.2(33)SXI1 Ok
4 0016.4778.7600 to 0016.4778.762f 1.1 8.4(1) 12.2(33)SXI1 Ok
5 0016.c848.3880 to 0016.c848.3883 5.6 8.5(2) 12.2(33)SXI1 Ok

Mod Sub-Module Model Serial Hw Status
---- --------------------------- ------------------ ----------- ------- -------
1 Distributed Forwarding Card WS-F6700-DFC3A SAL08290N34 2.2 Ok
5 Policy Feature Card 3 WS-F6K-PFC3B SAL1208GUY6 2.3 Ok
5 MSFC3 Daughterboard WS-SUP720 SAL1208GSV6 3.1 Ok

Mod Online Diag Status
---- -------------------
1 Pass
2 Pass
3 Pass
4 Pass
5 Pass

and the code version:

Uptime for this control processor is 5 days, 19 hours, 50 minutes
Time since Br03-CORE-6506-1 switched to active is 5 days, 19 hours, 49 minutes
System returned to ROM by power cycle at 15:33:41 UTC Wed Apr 30 2014 (SP by power on)
System restarted at 16:03:27 CDT Tue Jun 10 2014
System image file is "sup-bootdisk:s72033-adventerprisek9_wan-mz.122-33.SXI13.bin"
Last reload reason: reload

for some reason it's not supporting "mpls label protocol ldp"

any ideas?

Thanks

Greg

Nagendra Kumar Nainar · ‎06-18-2014

Greg,

MPLS is supported in SUP720-3B. Please check the below datasheet,

http://www.cisco.com/c/en/us/products/collateral/switches/catalyst-6500-series-switches/product_data_sheet09186a0080159856.html

Can you share the error you are getting while tryign to configure the command?. Were you able to enable mpls ip under interfaces?.

--Nagendra

bhnegi · ‎07-10-2014

I believe the reason is that your have WS-F6700-DFC3A on LC1 and my guess is system is falling into PFC3A mode.

Please see Table 1. DFC3 Supported Combinations on link below

http://www.cisco.com/c/en/us/products/collateral/switches/catalyst-6500-series-switches/prod_bulletin0900aecd8017a5db.html

Can you please collect the output of "show platform hardware pfc mode"

Best Regards,

Bheem

Sup720-3B - not showing to support MPLS / LDP