hallo every one!
i need setup vpls between two CPT 600 and can ping between 2 me3600 switches
between cpt 600 i was setup ospf and mpls and setup vpls, but my me3600 switch can not ping
what i do wrong?
my topology in attachment
this is my hardware configuration:
cpt 600 left
sh run
Building configuration...
Current configuration : 8779 bytes
!
! Last configuration change at 14:38:57 PST Sun Jan 16 2000
!
version 15.2
no service pad
service timestamps debug datetime msec
service timestamps log datetime msec
service password-encryption
!
!
ip cef distributed
!
!
!
mpls label range 4001 8000 static 16 4000
mpls label protocol ldp
no mpls traffic-eng auto-bw timers
bridge-domain 100
mode vpls
archive
log config
logging enable
username CISCO15 privilege 15 password 7 085A749EF5C07B9DD7
!
l2 vfi vpls-100-test manual
vpn id 100
bridge-domain 100
neighbor 172.168.0.2 encapsulation mpls
!
interface Loopback0
ip address 172.168.0.1 255.255.255.255
!
!
interface TenGigabitEthernet3/3
no ip address
carrier-delay msec 200
no keepalive
soak link notification 10
l2protocol peer cdp lacp
l2protocol forward stp vtp dtp pagp dot1x
service instance 100 ethernet
encapsulation dot1q 100
rewrite ingress tag pop 1 symmetric
bridge-domain 100
!
!
interface TenGigabitEthernet3/4
ip address 192.168.1.1 255.255.255.252
ip ospf network point-to-point
carrier-delay msec 200
mpls ip
mpls label protocol ldp
no keepalive
soak link notification 10
l2protocol peer cdp lacp
l2protocol forward stp vtp dtp pagp dot1x
!
!
router ospf 1
router-id 172.168.0.1
network 172.168.0.1 0.0.0.0 area 0
network 192.168.1.0 0.0.0.3 area 0
!
mpls ldp router-id Loopback0 force
!
!
control-plane
!
!
line con 0
line vty 0 4
privilege level 15
no login
line vty 5 6
privilege level 15
no login
!
end
switch me3600 left
sh run
Building configuration...
Current configuration : 2205 bytes
!
! Last configuration change at 07:25:22 UTC Sun Feb 9 2014
!
version 15.3
no service pad
service timestamps debug datetime msec
service timestamps log datetime msec
platform bfd allow-svi
!
!
vlan 11
!
!
interface Vlan11
ip address 10.10.10.1 255.255.255.0
!
!
interface TenGigabitEthernet0/2
description link_to_BP_840
switchport trunk allowed vlan 11
switchport mode trunk
!
cpt 600 right
192.1.0.2#show run
Building configuration...
Current configuration : 8779 bytes
!
! Last configuration change at 02:03:00 PST Mon Jan 17 2000
!
version 15.2
no service pad
service timestamps debug datetime msec
service timestamps log datetime msec
service password-encryption
!
ip cef distributed
!
!
mpls label range 4001 8000 static 16 4000
mpls label protocol ldp
no mpls traffic-eng auto-bw timers
bridge-domain 100
mode vpls
archive
log config
logging enable
username CISCO15 privilege 15 password 7 05703EDFDD950C82FC
!
l2 vfi vpls-100-test manual
vpn id 100
bridge-domain 100
neighbor 172.168.0.1 encapsulation mpls
!
interface Loopback0
ip address 172.168.0.2 255.255.255.255
!
interface TenGigabitEthernet3/3
no ip address
carrier-delay msec 200
no keepalive
soak link notification 10
l2protocol peer cdp lacp
l2protocol forward stp vtp dtp pagp dot1x
service instance 100 ethernet
encapsulation dot1q 100
rewrite ingress tag pop 1 symmetric
bridge-domain 100
!
!
interface TenGigabitEthernet3/4
ip address 192.168.1.2 255.255.255.252
ip ospf network point-to-point
carrier-delay msec 200
mpls ip
mpls label protocol ldp
no keepalive
soak link notification 10
l2protocol peer cdp lacp
l2protocol forward stp vtp dtp pagp dot1x
!
!
router ospf 1
router-id 172.168.0.2
network 172.168.0.2 0.0.0.0 area 0
network 192.168.1.0 0.0.0.3 area 0
!
!
mpls ldp router-id Loopback0 force
!
control-plane
!
!
line con 0
line vty 0 4
privilege level 15
no login
line vty 5 6
privilege level 15
no login
!
end
switch me3600 right
show run
Building configuration...
Current configuration : 2148 bytes
!
! Last configuration change at 07:27:24 UTC Sun Feb 9 2014
!
version 15.3
no service pad
service timestamps debug datetime msec
service timestamps log datetime msec
platform bfd allow-svi
!
!
vlan 11
!
!
interface Vlan11
ip address 10.10.10.2 255.255.255.0
!
!
interface TenGigabitEthernet0/2
description link_to_BP_873
switchport trunk allowed vlan 11
switchport mode trunk
!
cpt 600 left# show vfi
Legend: RT=Route-target, S=Split-horizon, Y=Yes, N=No
VFI name: vpls-100-test, state: up, type: multipoint
VPN ID: 100
Bridge-Domain 100 attachment circuits:
Neighbors connected via pseudowires:
Peer Address VC ID S
172.168.0.2 100 Y
192.1.0.2#show mpls l2transport ?
binding Display VC label binding information
checkpoint L2 transport checkpoint information
fsm Finite state machine counters
hw-capability Show MPLS L2 transport capability
memory AToM memory usage
pwid AToM dataplane pseudowire identifier usage
static-oam Static PW OAM show commands
summary Show summary of l2transport
vc Display VC(s) info for circuit transport over MPLS
cpt 600 left# show mpls l2transport vc 100
Local intf Local circuit Dest address VC ID Status
------------- -------------------------- --------------- ---------- ----------
VFI vpls-100-test \
VFI 172.168.0.2 100 UP
show mpls l2transport vc 100
Local intf Local circuit Dest address VC ID Status
------------- -------------------------- --------------- ---------- ----------
VFI vpls-100-test \
VFI 172.168.0.2 100 UP
cpt 600 left# show cdp neighbors
Capability Codes: R - Router, T - Trans Bridge, B - Source Route Bridge
S - Switch, H - Host, I - IGMP, r - Repeater, P - Phone,
D - Remote, C - CVTA, M - Two-port Mac Relay
Device ID Local Intrfce Holdtme Capability Platform Port ID
cpt 600 right Ten 3/4 131 R I CPT 600 Ten 3/4
me3600 left Ten 3/3 174 R S I ME-3600X- Ten 0/2
if every setup configurations is right, what i do wrong? way i cannot ping between 2 me3600 switches? please help me
