Hi everyone,I have a Cisco Switch 2960. With 2 vlan : vlan 195 : DATA : From f0/1 to f0/24 vlan 14 : VOICE : From f0/1 to f0/24 I config on Switch as below : enable config terminal no ip domain lookup lin con 0 logg syn exit logging console informati...
This community is for technical, feature, configuration and deployment questions.
For production deployment issues, please contact the TAC! We will not comment or assist with your TAC case in these forums.
Please see How to Ask the Community for Help for other troubleshooting best practices.
For production deployment issues, please contact the TAC! We will not comment or assist with your TAC case in these forums.
Please see How to Ask the Community for Help for other troubleshooting best practices.
Forum Posts
Has anyone done 2 factor authentication for Cisco ASAs? I am working on a solution for setting up 2 factor authentication to access the management interface of a cisco asa. We have cisco ISE that we can leverage for this. My question is has this b...
Hi, We have realized that authenticated users remain indefinitely authenticated. There is no type of timeout that closes the session. We have configured the reauthenticacion for 30 minutos but the users remain permanent.Why is not the timeout worki...
Hello, I was curious what the aaa command is that would allow local login via ssh in the event of an ISE failure. Currently I have the following on my Nexus routers/switches: aaa authentication login default group ISE aaa authentication log...
This is for ISE 1.3+do you know if it's possible to remove the Device registration status from the MyDevices portal (ISE 1.4)? By default the status is displayed (Registered/Pending). My Customer wants to get rid of this column in general:
Hello Team,Customer wants to use "ISE-2.4.0.357-virtual-SNS3595-Medium-1200GBHD-64GBRAM-16CPU.ova" (SNS3595 spec) and deploy it. They want 1.2 TB of hard drive space. According to the ISE installation guide, they should build from ISO if they want to...
HelloIt appears that our production ISE 2.3 patch 1 has had this error for a few months and it's gone unnoticed. It says to contact the TAC and I have done some searches. Apparently the resolution is to runapplication configure iseSelect option 7 t...
Resolved! IE1000 Version 1.7 AAA support
Hello All, i installed IE1000 switch and upgrade it to 1.7 last month (For AAA Support). i try to configure and add him to ISE, but i get shell profile error in the Tacacs event log. is anyone have any idea or knowledge for the Shell Profile config...
I have total three SNS 3595 & one of them are Primary PAN & other one is PSN & one is MNT. while registering the node is successful but after restart the service automatically & few min latter its shows registration / sync failed please deregister & ...
Hello All, We have a setup in the lab where we are using passive ID with ISE and as a result the username gets mapped to multiple IP addresses. Please see the attached document for the topology. Lab components: ASAv Virtual ISE 2.3 AD – Server 2016 W...
Hi Experts, Recently we have deployed a new ISE 2.4 cluster. So there are some use cases that we wanted to check and create a guidelines document for these scenarios. I went to the command line of the primary admin, ran halt. The primary went down, a...
Hello, I can manage Self-Signed Guest Accounts through Manage Accounts in ISE menu (Work Centers > Guest Access > Manage Accounts. It open session on port 9002. How can I manage this Self-Signed guest accounts through common sponsor portal on port 8...
Hi All,Please am having a problem where by the network setup assistant couldn't connect to the server, So it can't download the Anyconnect installation files from I.S.E server. Have configure the Anyconnect Configuration and associated it with a Clie...
Resolved! ACS and ISE authentication.
Hello, My customer has AAA using ACS for all network devices and guest wifi access configured through ISE. Now they are planning use profiling for endpoints, posturing with 802.1x authentication,authorization on wired users through ISE. They have r...
Hello Team, We tried to generate Accounting Report but we found out that is missing two columns which are needed by our compliance team. How do we address this concern.
