cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
Announcements

This community is for technical, feature, configuration and deployment questions.
For production deployment issues, please contact the TAC! We will not comment or assist with your TAC case in these forums.
Please see How to Ask the Community for Help for other best practices.

1865
Views
5
Helpful
8
Replies

Delete DNS entry on ACS 5.3

Hi to all

I want to remove the actual DNS servers:

Enter configuration commands, one per line.  End with CNTL/Z.

acsbrou/admin(config)# ip name-server 192.168.1.103

% Name-server table is full; 192.168.1.103 not added

acsbrou/admin(config)#

Anyone nows how to clear the table?

Thanks

1 ACCEPTED SOLUTION

Accepted Solutions
edwjames
Participant

Hi Sebastian,

The List might already be full.

Try "no ip name-server" and then try adding the new ones.

**Share your knowledge. It’s a way to achieve immortality.
--Dalai Lama**

Please Rate if helpful.
Regards
Ed

**Share your knowledge. It’s a way to achieve immortality. --Dalai Lama** Please Rate if helpful. Regards Ed

View solution in original post

8 REPLIES 8
edwjames
Participant

Hi Sebastian,

The List might already be full.

Try "no ip name-server" and then try adding the new ones.

**Share your knowledge. It’s a way to achieve immortality.
--Dalai Lama**

Please Rate if helpful.
Regards
Ed

**Share your knowledge. It’s a way to achieve immortality. --Dalai Lama** Please Rate if helpful. Regards Ed

View solution in original post

Your are the best! thanks a lot Ed.

Regards from LATAM!

Sebas

Hey Ed, Look at this:

This is the message when I try to add Active Directory:

Connection test to 'lan.vusecurity.com' failed.

Further information on status:

   - Can not resolve network address

An this one when I try DNS from the console:

Trying "lan.vusecurity.com"

;; ->>HEADER<<- opcode: QUERY, status: NOERROR, id: 60888

;; flags: qr aa rd ra; QUERY: 1, ANSWER: 2, AUTHORITY: 0, ADDITIONAL: 4

;; QUESTION SECTION:

;lan.vusecurity.com.            IN      ANY

;; ANSWER SECTION:

lan.vusecurity.com.     3600    IN      NS      jerico.lan.vusecurity.com.

lan.vusecurity.com.     3600    IN      SOA     jerico.lan.vusecurity.com. hostmaster. 4 900 600 86400 3600

;; ADDITIONAL SECTION:

jerico.lan.vusecurity.com. 3600 IN      A       192.168.1.137

jerico.lan.vusecurity.com. 3600 IN      A       192.168.1.128

jerico.lan.vusecurity.com. 3600 IN      A       192.168.1.103

jerico.lan.vusecurity.com. 3600 IN      A       192.168.56.1

Received 167 bytes from 192.168.1.103#53 in 1 ms

Any ideas?

Sebas

Sometimes, this is due the ports in between that are not open or sometimes its a wrong test connection message.

Are you able to save configuration or does that give an error as well?

**Share your knowledge. It’s a way to achieve immortality.
--Dalai Lama**

Please Rate if helpful.
Regards
Ed

**Share your knowledge. It’s a way to achieve immortality. --Dalai Lama** Please Rate if helpful. Regards Ed

Thanks again,

Port are open, both ACS and AD are on the same LAN, inside the same VMware.

acsbrou/admin# Write memory

Generating configuration...

Writing configuration works ok.

¿?

What do you get when you perform save configuration?

**Share your knowledge. It’s a way to achieve immortality.
--Dalai Lama**

Please Rate if helpful.
Regards
Ed

**Share your knowledge. It’s a way to achieve immortality. --Dalai Lama** Please Rate if helpful. Regards Ed

you mean with "write memory"?

Generating configuration...

Thats all

Not exactly, I mean the save changes button on the AD configuration page.

**Share your knowledge. It’s a way to achieve immortality.
--Dalai Lama**

Please Rate if helpful.
Regards
Ed

**Share your knowledge. It’s a way to achieve immortality. --Dalai Lama** Please Rate if helpful. Regards Ed
Content for Community-Ad

This widget could not be displayed.