Alarm snmp on the fan detected but not visible on my switch

[mhassine]

Hello, 

I have configure an alarm snmp for the fan status. I use the MIB "CISCO-ENVMON-MIB". 

Here are the different state of a fan : 

CiscoEnvMonState ::= TEXTUAL-CONVENTION

        STATUS  current

        DESCRIPTION

                "Represents the state of a device being monitored.

                 Valid values are:

                 normal(1):  the environment is good, such as low

                                    temperature.

                 warning(2): the environment is bad, such as temperature

                                    above normal operation range but not too

                                    high.

                 critical(3):   the environment is very bad, such as

                                    temperature much higher than normal

                                    operation limit.

                 shutdown(4): the environment is the worst, the system

                                    should be shutdown immediately.

                 notPresent(5): the environmental monitor is not present,

                                    such as temperature sensors do not exist.

                 notFunctioning(6): the environmental monitor does not

                                    function properly, such as a temperature

                                    sensor generates a abnormal data like

                                    1000 C.

My snmp tool return an alarm with the argument : notFunctioning (6) on a power supply's fan  

When i connect on my switch, i check the fan status with the command show environment status, i can see the fan sensor is good. (my alarm is on the equipment with the red arrow)

Why have I an alarm snmp on this fan ? 

Thanks for your answers. 

Regards, 

P.S : Sorry for my english, It is maybe bad. 

[balaji.bandi]

what device is this, post show version and show environment full.

[mhassine]

Hello, 

oh yes i forget to indicate my device. The device is WS-C4500X-16.

device#sh environment status

Executing the command on VSS member switch role = VSS Active, id = 1

Power Fan Inline
Supply Model No Type Status Sensor Status
------ ---------------- --------- ----------- ------- -------
PS1 PWR-C4KX-750AC-R AC 750W good good n.a.
PS2 PWR-C4KX-750AC-R AC 750W good good n.a.

Power supplies needed by system : 1
Power supplies currently available : 2

Chassis Type : WS-C4500X-16

Power consumed by backplane : 0 Watts

Switch Bandwidth Utilization : 0%

Supervisor Led Color : Green

Module 1 Status Led Color : Green

Beacon Led Status : off

Fan trays needed by system : 4
Fan trays currently available : 5
Chassis fan tray direction : FrontToBack

Fantray 1 : dir : FrontToBack status : Good
Fantray 2 : dir : FrontToBack status : Good
Fantray 3 : dir : FrontToBack status : Good
Fantray 4 : dir : FrontToBack status : Good
Fantray 5 : dir : FrontToBack status : Good

Fantray removal timeout : 180

Power consumed by Fantray : 90 Watts

Executing the command on VSS member switch role = VSS Standby, id = 2

Power Fan Inline
Supply Model No Type Status Sensor Status
------ ---------------- --------- ----------- ------- -------
PS1 PWR-C4KX-750AC-R AC 750W good good n.a.
PS2 PWR-C4KX-750AC-R AC 750W good good n.a.

Power supplies needed by system : 1
Power supplies currently available : 2

Chassis Type : WS-C4500X-16

Power consumed by backplane : 0 Watts

Switch Bandwidth Utilization : 0%

Supervisor Led Color : Green

Module 11 Status Led Color : Green

Beacon Led Status : off

Fan trays needed by system : 4
Fan trays currently available : 5
Chassis fan tray direction : FrontToBack

Fantray 1 : dir : FrontToBack status : Good
Fantray 2 : dir : FrontToBack status : Good
Fantray 3 : dir : FrontToBack status : Good
Fantray 4 : dir : FrontToBack status : Good
Fantray 5 : dir : FrontToBack status : Good

Fantray removal timeout : 180

Power consumed by Fantray : 90 Watts

device#sh version
Cisco IOS Software, IOS-XE Software, Catalyst 4500 L3 Switch Software (cat4500e-UNIVERSALK9-M), Version 03.07.00.E RELEASE SOFTWARE (fc4)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2014 by Cisco Systems, Inc.
Compiled Sun 07-Dec-14 22:13 by prod_rel_team

Cisco IOS-XE software, Copyright (c) 2005-2014 by cisco Systems, Inc.
All rights reserved. Certain components of Cisco IOS-XE software are
licensed under the GNU General Public License ("GPL") Version 2.0. The
software code licensed under GPL Version 2.0 is free software that comes
with ABSOLUTELY NO WARRANTY. You can redistribute and/or modify such
GPL code under the terms of GPL Version 2.0.
(http://www.gnu.org/licenses/gpl-2.0.html) For more details, see the
documentation or "License Notice" file accompanying the IOS-XE software,
or the applicable URL provided on the flyer accompanying the IOS-XE
software.

ROM: 15.0(1r)SG11
device uptime is 6 years, 24 weeks, 1 day, 2 hours, 59 minutes
Uptime for this control processor is 6 years, 24 weeks, 1 day, 3 hours, 1 minute
System returned to ROM by reload
System restarted at 15:13:08 CEST Wed Aug 26 2015
System image file is "bootflash:cat4500e-universalk9.SPA.03.07.00.E.152-3.E.bin"
Jawa Revision 2, Winter Revision 0x0.0x41

Last reload reason: reload

This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.

A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html

If you require further assistance please contact us by sending email to
export@cisco.com.

License Information for 'WS-C4500X-16'
License Level: ipbase Type: Permanent
Next reboot license Level: ipbase

cisco WS-C4500X-16 (MPC8572) processor (revision 9) with 4194304K bytes of physical memory.
Processor board ID JAE1915053P
MPC8572 CPU at 1.5GHz, Cisco Catalyst 4500X
Last reset from Reload
2 Virtual Ethernet interfaces
32 Ten Gigabit Ethernet interfaces
511K bytes of non-volatile configuration memory.

Configuration register is 0x102

Regards,