11-14-2013 08:42 PM
Though the Cisco Prime Infrastructure Compatibility Matrix list out that 7.2.111.3 is supported for PI 2.0
I am not able to add the controller to the PI 2.0.
The Reachability Status always shown "Unknow" and SNMP Status always shown "No response for SNMP Get".
There is no firewall between the WLC and PI.
And ping test shows it is reachable.
If I try to add controller by non-management port (I know it is not work but I want to try the reachability), the Reachability Status shown "Reachable" but the SNMP Status always shown error.
And if I use some SNMP testing software to test the SNMP port. SNMP can be quoted.
I have try to lower down the "Maximum VarBinds per Get PDU" but no luck.
Any thing I can do to troubleshoot the problem?
Solved! Go to Solution.
11-15-2013 02:20 AM
Hi, please check on 5508 wlc:
Did u enable snmp on wlc??
mrncciew.com/2013/02/14/configuring-snmp-on-wlc/
Regards
Please rate if it helps
Sent from Cisco Technical Support iPhone App
11-15-2013 12:03 AM
Hi,
did u enter the correct community name:
put the management interface ip address and also put the right community name.
As per screenshot:
Hope it helps
Regards
Please rate helpful post.
11-15-2013 12:47 AM
Thanks, sandeepchoudhary21
Yes, I have tried with the new Community and "prviate". But none of them work.
Also, I have tried SNMP v1 and v3. They are also not working.
11-15-2013 01:08 AM
Hi
Did u tried as per this document:
https://supportforums.cisco.com/docs/DOC-29006#SNMP
Please check if firewall isn't blocking SNMP to/from the WLC.
Regards
Please rate helpful post.
11-15-2013 02:00 AM
Yes, I follow the procedure but it does not work.
Another update:
I add another WLC with version 7.0.98.0. It is fine.
And I setup another new PI 2.0 and new temporary WLC5508 with 7.2.111.3 to test. It work fine also......
So, I am wondering the existing 7.2 WLC have problem in responsing the SNMP Get. But I dont have any idea to test....
Do anyone have idea to test the snmp connection between PI and WLC?
11-15-2013 02:20 AM
Hi, please check on 5508 wlc:
Did u enable snmp on wlc??
mrncciew.com/2013/02/14/configuring-snmp-on-wlc/
Regards
Please rate if it helps
Sent from Cisco Technical Support iPhone App
11-17-2013 11:17 PM
Yes, the WLC enabled the snmp. I used some snmp tools to quote and the result is positive.
There is some update.
I tried Prime infrastructure 1.4 to add the WLC. However, it shows the same as that of PI 2.0.
There should be some problem for the WLC. I will try reboot later on.
11-22-2013 12:15 AM
Finally, I add the controller by another non-management interface...
PI2.0 is not ready for enterpries as discussed in another discussion.
11-22-2013 12:20 AM
Glad that u resolved the problem thanks for sharing.
Please mark this question as answered so that it may help others.
Regards
Sent from Cisco Technical Support iPhone App
06-09-2015 11:15 PM
06-11-2015 01:55 AM
No such error is found. Btw, the PI 2.2 is released now. I believe such bug has been fixed.
06-11-2015 02:13 AM
I think Bug Version 7.6.120.0
I tested PI2.2 and WLC 7.6.130.10 7.6.130.21 is no problem
But PI 2.2 and WLC 7.6.120.0 is problem found can not remove device and update and audit
06-11-2015 02:34 AM
There is a "star" for 7.6.130. Use it anyway.
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide