cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
1970
Views
5
Helpful
4
Replies

Detailed software reports Cisco Prime Infrastructure 2.0

ShaunGreen
Level 1
Level 1

Hi All,

We are running CPI 2.0. managing approximately 280 routers/switches. 2940's, 4900's 3700's and Nexus 5 and 7K's.

We have tried to run one type of software per device group where possible, but haven't fully succeeded.

I'm trying to find a away if possible of using CPI to carry out a report on the software versions per device group to see if there are any software advisories, end of support notices, compliance reports etc.

Does anyone know if this is possible, or what's the best I could hope for from CPI?

Thank you in advance for any information you can offer.

Si.

1 Accepted Solution

Accepted Solutions

Hi,

 

You can run the  : PSIRT Summary report

This reports displays a summary of Software versions in the network affected by the posted Cisco Product Security Notices.

 

****IMP***

you must enable the compliance service, restart the server, and synchronize inventory to view and generate the PSIRT reports.

http://www.cisco.com/c/en/us/td/docs/net_mgmt/prime/infrastructure/2-0/administrator/guide/PIAdminBook/config_server_settings.html#wp1082023

 

Also check the below Post :

https://supportforums.cisco.com/discussion/11923841/cisco-prime-infrastructure-eoleos-and-psirt-reports

 

check the below links:

http://www.cisco.com/c/en/us/td/docs/net_mgmt/prime/infrastructure/2-0/user/guide/prime_infra_ug/reps.html#pgfId-1059921

 

Hope this will help

 

Thanks-

Afroz

***Ratings Encourages Contributors ****

Thanks- Afroz [Do rate the useful post] ****Ratings Encourages Contributors ****

View solution in original post

4 Replies 4

AFROJ AHMAD
Cisco Employee
Cisco Employee

Hi,

 

Did you tried :

Report > Report Launch Pad > Device > Detailed Software

 

there you will see an option " REPORT TYPE" , you can select  'switches n hubs' or Routers  etc..  I am afraid it will not list the port group.

 

But you can Export the result of the report and achive your goal.

 

hope it will help

Thanks-

Afroz

[Do rate the useful post]

***Ratings Encourages Contributors***

Thanks- Afroz [Do rate the useful post] ****Ratings Encourages Contributors ****

Thanks for your reply Afroz.

I was hoping that there was a way that CPI could take this information from the report and run say a software advisory search for the listed IOS and report on them.

I can obviously check security notices manually from the listed software, but it would be nice if there was an automated process

Hi,

 

You can run the  : PSIRT Summary report

This reports displays a summary of Software versions in the network affected by the posted Cisco Product Security Notices.

 

****IMP***

you must enable the compliance service, restart the server, and synchronize inventory to view and generate the PSIRT reports.

http://www.cisco.com/c/en/us/td/docs/net_mgmt/prime/infrastructure/2-0/administrator/guide/PIAdminBook/config_server_settings.html#wp1082023

 

Also check the below Post :

https://supportforums.cisco.com/discussion/11923841/cisco-prime-infrastructure-eoleos-and-psirt-reports

 

check the below links:

http://www.cisco.com/c/en/us/td/docs/net_mgmt/prime/infrastructure/2-0/user/guide/prime_infra_ug/reps.html#pgfId-1059921

 

Hope this will help

 

Thanks-

Afroz

***Ratings Encourages Contributors ****

Thanks- Afroz [Do rate the useful post] ****Ratings Encourages Contributors ****

Thanks Afroz, that worked perfectly.

I've received a LOT of information on the report, but it's got all the information I require.

Thanks for the links too. Hopefully in the next update CPI will be able to do the EOx for the hardware.

Thanks again.
Simon.

Getting Started

Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: