01-04-2013 06:57 AM
Does anyone know if there is a MIB available for the EHWIC-4G-LTE-V card that would allow me to monitor the current RSSI level?
If I issue the command "show cell 0/1/0 radio" on my Cisco2911 router, I get the following info. I'd like to monitor the "Current RSSI" level in Solarwinds.
Router>show cell 0/1/0 radio
Radio power mode = ON
Current RSSI = -67 dBm
LTE Technology Preference = AUTO
LTE Technology Selected = LTE
Solved! Go to Solution.
02-22-2013 10:28 AM
The cisco-WAN-3G mib worked for me before this newest IOS of 15.2(4)M2 I'm using 15.1(4)M4 and able able to get SS from device.
Get signal Strength
.1.3.6.1.4.1.9.9.661.1.3.4.1.1.1.18
Get phone #
.1.3.6.1.4.1.9.9.661.1.3.1.1.4.18
Get SIM
.1.3.6.1.4.1.9.9.661.1.3.1.1.3.18
Get IMEI
.1.3.6.1.4.1.9.9.661.1.3.1.1.2.18
Roaming status
.1.3.6.1.4.1.9.9.661.1.1.1.6.18
1 unknown, 2 roaming, 3 home
01-31-2013 02:45 PM
I've been looking at the MIBs and haven't been able this either, but I'm very interseted.
08-25-2016 01:21 PM
I got it by swapping the 18 for 29 on 15.4:
.1.3.6.1.4.1.9.9.661.1.3.4.1.1.1.29
SNMPv2-SMI::enterprises.9.9.661.1.3.4.1.1.1.29 = INTEGER: -49
02-22-2013 10:28 AM
The cisco-WAN-3G mib worked for me before this newest IOS of 15.2(4)M2 I'm using 15.1(4)M4 and able able to get SS from device.
Get signal Strength
.1.3.6.1.4.1.9.9.661.1.3.4.1.1.1.18
Get phone #
.1.3.6.1.4.1.9.9.661.1.3.1.1.4.18
Get SIM
.1.3.6.1.4.1.9.9.661.1.3.1.1.3.18
Get IMEI
.1.3.6.1.4.1.9.9.661.1.3.1.1.2.18
Roaming status
.1.3.6.1.4.1.9.9.661.1.1.1.6.18
1 unknown, 2 roaming, 3 home
02-22-2013 12:58 PM
Thank you Daniel. I will give this a shot.
02-22-2013 01:00 PM
let me know if i can assist.
02-27-2013 03:20 PM
No dice on 15.3. I'll try falling back to 15.1 to see if that work. Thanks for sharing those Daniel.
03-01-2013 11:25 AM
I got it working on 15.1(4)M4, as well. Next step is creating alerts based off the results of the custom poller. Thanks Daniel!
03-01-2013 11:37 AM
Same, I went back to 15.1 and it was working. For our mobile "network in a box" I'm going to create an arduino based microcontroller to does SNMP polls and then displays the RSSI on a small LCD dispaly for remote users to see.
02-10-2014 08:46 AM
Reverting back to 15.1 isn't possible anymore. Cisco doesn't support the LTE cards with newer firmware on 15.1. I had to move to 15.2 and am now unable to monitor RSSI. Anyone find a way to get this value via SNMP on 15.2 yet?
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide