cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
6686
Views
3
Helpful
4
Replies

Need to understand Loopback interface, specifically in OSPF

sheryarqazi4
Level 1
Level 1

Need to understand Loopback interface, specifically in OSPF, so please elaborate ?

3 Accepted Solutions

Accepted Solutions

balaji.bandi
Hall of Fame
Hall of Fame

Loopback interface is useful because it is an interface with an IP address which never goes down and always stay up.(until admin shutdown)

In case of OSPF, without a specifically defined Router ID, OSPF will pick a Router ID on its own. It chooses the Router ID from the IP addresses of the configured and enabled interfaces.

 

If you have multiple path still Loopback is reachable to nework.

BB

***** Rate All Helpful Responses *****

How to Ask The Cisco Community for Help

View solution in original post

Martin L
VIP
VIP

see https://community.cisco.com/t5/routing/loopback-interface-influence-in-ospf/m-p/3053102

https://community.cisco.com/t5/routing/loopback-on-ospf/m-p/1677821

 

as mentioned by BB, loopback is important in OSPF (and BGP as well);  OSPF picks its Router ID among highest IPs that are UP UP state BUT it prefers Loopbacks.  OSPF will pick IP of a Loopback interface even if that IP is lower then IP from regular interfaces.  Still, Router ID should be set manually - recommended practice. 

 

Regards, ML
**Please Rate All Helpful Responses **

View solution in original post

Previous responses have focused on OSPF use of loopback interfaces for Router ID. There is another aspect of loopback interfaces use in OSPF that we should point out. You might configure something like this

interface loopback1

ip address 192.168.1.1 255.255.255.0

If you configure an OSPF network statement for this interface/network you might expect that OSPF would advertise a /24. But OSPF recognizes that the loopback is not a normal interface and will advertise the route as /32. If you want to have OSPF advertise the /24 under the interface configuration you need to specify an OSPF network type.

HTH

Rick

View solution in original post

4 Replies 4

balaji.bandi
Hall of Fame
Hall of Fame

Loopback interface is useful because it is an interface with an IP address which never goes down and always stay up.(until admin shutdown)

In case of OSPF, without a specifically defined Router ID, OSPF will pick a Router ID on its own. It chooses the Router ID from the IP addresses of the configured and enabled interfaces.

 

If you have multiple path still Loopback is reachable to nework.

BB

***** Rate All Helpful Responses *****

How to Ask The Cisco Community for Help

Martin L
VIP
VIP

see https://community.cisco.com/t5/routing/loopback-interface-influence-in-ospf/m-p/3053102

https://community.cisco.com/t5/routing/loopback-on-ospf/m-p/1677821

 

as mentioned by BB, loopback is important in OSPF (and BGP as well);  OSPF picks its Router ID among highest IPs that are UP UP state BUT it prefers Loopbacks.  OSPF will pick IP of a Loopback interface even if that IP is lower then IP from regular interfaces.  Still, Router ID should be set manually - recommended practice. 

 

Regards, ML
**Please Rate All Helpful Responses **

Previous responses have focused on OSPF use of loopback interfaces for Router ID. There is another aspect of loopback interfaces use in OSPF that we should point out. You might configure something like this

interface loopback1

ip address 192.168.1.1 255.255.255.0

If you configure an OSPF network statement for this interface/network you might expect that OSPF would advertise a /24. But OSPF recognizes that the loopback is not a normal interface and will advertise the route as /32. If you want to have OSPF advertise the /24 under the interface configuration you need to specify an OSPF network type.

HTH

Rick

I am glad that our explanations have been helpful. Thank you for marking this question as solved. This will help other participants in the community to identify discussions which have helpful information. This community is an excellent place to ask questions and to learn about networking. I hope to see you continue to be active in the community.

HTH

Rick

Review Cisco Networking for a $25 gift card