10-02-2012 05:42 AM
All,
First of all, this board has been instramental in helping us through a number of issues we have had in building out our new corporate headquarters. I do have a netflow question that has got me this time. Below is my netflow config on a set of 4, 3750's stackwise running IOS 15. I am not getting an packet leaving the switches nor am I seeing any on my cacti server. I have checked the server and not blocking on the iptables firewall. Below in my config:
flow record TWI-2E-SW1
match ipv4 destination address
collect counter flows
!
!
flow exporter Cacti
description Cacti Server
destination 10.15.10.18
transport udp 2055
export-protocol netflow-v5
!
!
flow monitor Cacti
description Cacti Netflow Tool
record TWI-2E-SW1
exporter Cacti
!
ip flow-export version 5
ip flow-export destination 10.15.10.18 2055
ip flow-export destination 10.15.10.238 2055
!
interface GigabitEthernet1/1/4
description Primary East connection to TWI-DC-E1 port 7/2
switchport trunk encapsulation dot1q
switchport mode trunk
ip flow ingress
ip flow egress
ip flow monitor Cacti layer2-switched input
ip flow monitor Cacti layer2-switched output
interface GigabitEthernet4/1/4
description Secondary East connection to TWI-DC-W1 port 7/22
switchport trunk encapsulation dot1q
switchport mode trunk
ip flow ingress
ip flow egress
_______________________
Show IP flow export
k
TWI-2E-SW1#sh ip flow export
Flow export v5 is enabled for main cache
Export source and destination details :
VRF ID : Default
Destination(1) 10.15.10.18 (2055)
Destination(2) 10.15.10.238 (2055)
Version 5 flow records
0 flows exported in 0 udp datagrams
0 flows failed due to lack of export packet
0 export packets were sent up to process level
TWI-2E-SW1#
Thanks again
10-02-2012 07:57 AM
10-02-2012 08:31 AM
We are using the following:
C3KX-NM-1G= 1 GB Network Module
GLC-SX-MM= SFP GBICS
I am looking for the revision number as well.
Revision info:
General SFP Information
-----------------------------------------------
Identifier : 0x03
Connector : 0x07
Transceiver : 0x00 0x00 0x00 0x01 0x00 0x00 0x00 0x00
Encoding : 0x01
BR_Nominal : 0x0D
Vendor Name : CISCO-FINISAR
Vendor Part Number : FTLF8519P2BCL-C5
Vendor Revision : 0x41 0x20 0x20 0x20
Vendor Serial Number : FNS16330EY4
--------------------------------------------
10-02-2012 09:31 AM
10-02-2012 11:24 AM
Crud, I was worried about that when I saw your whitepaper. If I can sneak another question in, Same subject but 6500.
I have a SUP-2T-10G and want to apply on gig module blabe (WS-6724-SFP). Am I goign to have problems. I continue to research this to see if supported. also, I have a vlan directly connected to my firewalls. Can I add to vlan at minimum.
thansk as always.
10-02-2012 03:23 PM
You're welcome.
You should be able to setup a Netflow export on a 6509 with SUP-2T-10G. See this helpful reference:
http://www.plixer.com/blog/cisco-netflow/catalyst-6509-netflow-support/
You could also use your firewall, assuming it's a Cisco ASA.
Please rate helpful replies.
10-02-2012 03:53 PM
Here is my problem. I believe all those are for IOS 12. I am running Version 15.0(1)SY1 on my 6500s, and having a devil of a time finding documents on this code. I am pretty confident the commands have changed. Any docs you found that can help me.
thanks.
10-02-2012 03:58 PM
The source documentation for configuring Flexible NetFlow on IOS 15.0SY can be found here:
http://www.cisco.com/en/US/docs/ios-xml/ios/fnetflow/configuration/15-0sy/fnf-15-0sy-book.html
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide