cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
5794
Views
0
Helpful
10
Replies

Port status on Cisc 9300 when Etherchannel

giangle
Level 1
Level 1

Hi all

Last week, I configured EtherChannel port between 2 Cisco 9300, network diagram:

 

       Cisco 9300 (Office)=====Leaseline ======= Cicso 9300 (DataCenter ISP)

 

In 9300 (Office):

Catalyst L3 Switch Software (CAT9K_IOSXE), Version 16.6.5

 

Group Port-channel Protocol Ports
------+-------------+-----------+-----------------------------------------------
93 Po93(SU) LACP Gi1/0/1(P) Gi1/0/8(P)

 

CoreSW_TV#show interfaces g1/0/8 stat
GigabitEthernet1/0/8
Switching path Pkts In Chars In Pkts Out Chars Out
Processor 0 0 28075 3281940
Route cache 0 0 0 0
Distributed cache 0 0 0 0
Total 0 0 28075 3281940

 

CoreSW_TV#show interfaces g1/0/1 stat
GigabitEthernet1/0/1
Switching path Pkts In Chars In Pkts Out Chars Out
Processor 0 0 2393477 277463956
Route cache 0 0 0 0
Distributed cache 0 0 0 0
Total 0 0 2393477 277463956

 

But led status in port G1/0/8 is amber. It's not green. Please explain and help me to fix this issue.

 

Thanks,

Giang Le

 

1 Accepted Solution

Accepted Solutions

change this one as below and let us know, how it goes.

 

interface GigabitEthernet1/0/1
switchport access vlan 93
switchport mode access
channel-group 93 mode active
end

 

Office_SW#show run int g1/0/8
Building configuration...

Current configuration : 120 bytes
!
interface GigabitEthernet1/0/8
switchport access vlan 93
switchport mode access
channel-group 93 mode active
end

 

BB

***** Rate All Helpful Responses *****

How to Ask The Cisco Community for Help

View solution in original post

10 Replies 10

marce1000
VIP
VIP

 

 - Issue the command show logging when the port get's connected ; check if there is more info.

   M.



-- ' 'Good body every evening' ' this sentence was once spotted on a logo at the entrance of a Weight Watchers Club !

Hi marce1000.

This is a log from log server in Cisco 9300 (office)

 

%ETC-5-L3DONTBNDL2: Gi1/0/8 suspended: LACP currently not enabled on the remote port.

 

 

Can you post both the side configuration related to that port-channel?

 

%ETC-5-L3DONTBNDL2: Gi1/0/8 suspended: LACP currently not enabled on the remote port.

 

above errors show far end not configured.

 

BB

***** Rate All Helpful Responses *****

How to Ask The Cisco Community for Help

Hi,

This is my configure at far end:

 

Group Port-channel Protocol Ports
------+-------------+-----------+-----------------------------------------------
93 Po93(SU) LACP Gi1/0/6(P) Gi2/0/6(P)

 

In far end, we use stack 9300 and use G1/0/6 for Stack-SW-01, G2/0/6 for Stack-SW-02. connection from Data Center to Office via ISP lease line.

 

Regards,

Giang Le

That is not a configuration that is the output of EtherChannel output.

 

post below information : (given example, post both the side).

 

 

show run interface gi 1/0/1

show run interface gi 1/0/8

show run inter port-channel 93

 

 

show run interface gi 1/0/6

show run interface gi 2/0/6

show run inter port-channel 93

BB

***** Rate All Helpful Responses *****

How to Ask The Cisco Community for Help

Hi balaji.bandi.

I sent you my configre in both side:

----------------------------------------------

Data Center ISP:

CoreSW#show run int g1/0/6
Building configuration...

Current configuration : 158 bytes
!
interface GigabitEthernet1/0/6
switchport access vlan 93
switchport mode access
channel-group 93 mode active
end

 

CoreSW#show run int g2/0/6
Building configuration...

Current configuration : 158 bytes
!
interface GigabitEthernet2/0/6
switchport access vlan 93
switchport mode access
channel-group 93 mode active
end

 

CoreSW#show run int port-channel 93
Building configuration...

Current configuration : 83 bytes
!
interface Port-channel93
switchport access vlan 93
switchport mode access
end

----------------------------------------------

Office:

Office_SW#show run int g1/0/1
Building configuration...

Current configuration : 150 bytes
!
interface GigabitEthernet1/0/1
switchport access vlan 93
switchport mode access
channel-group 93 mode passive
end

 

Office_SW#show run int g1/0/8
Building configuration...

Current configuration : 120 bytes
!
interface GigabitEthernet1/0/8
switchport access vlan 93
switchport mode access
channel-group 93 mode passive
end

 

Office_SW#show run int port-channel 93
Building configuration...

Current configuration : 83 bytes
!
interface Port-channel93
switchport access vlan 93
switchport mode access
end

 

----------------------------------------------

Output result:

Office:

Group Port-channel Protocol Ports
------+-------------+-----------+-----------------------------------------------
93 Po93(SU) LACP Gi1/0/1(P) Gi1/0/8(P)

 

DataCenter ISP:

Group Port-channel Protocol Ports
------+-------------+-----------+-----------------------------------------------
14 Po14(SU) LACP Gi1/0/21(P) Gi2/0/21(P)
15 Po15(SU) LACP Gi1/0/22(P) Gi2/0/22(P)
93 Po93(SU) LACP Gi1/0/6(P) Gi2/0/6(P)

 

REgards

Giang 

change this one as below and let us know, how it goes.

 

interface GigabitEthernet1/0/1
switchport access vlan 93
switchport mode access
channel-group 93 mode active
end

 

Office_SW#show run int g1/0/8
Building configuration...

Current configuration : 120 bytes
!
interface GigabitEthernet1/0/8
switchport access vlan 93
switchport mode access
channel-group 93 mode active
end

 

BB

***** Rate All Helpful Responses *****

How to Ask The Cisco Community for Help

Hi balaji.bandi,
It worked with your configuration.
I have a question. At local office, I was running with Active/Passive configuration. But between office - Data Center ISP, this mode didn't work. I wonder what's difference on this except Active sent out LACP packet.

Regards,
Giang Le

LACP always Active initiate the connection and Passive listens ( passive do not have capabilities to initiate)

 

If both set ACTIVE, anyone can initiate the connection. no need to wait for a partner to initiate the connection, your side shut and unshut should form the port-channel.

 

Maybe your Case Passive and Active should work. ( if you like to try After Passive side up and running, Active side shut and un shut to form the port-channel).

 

But i would prefer to have Active/Active, so you have both the side control.

 

make sense?

 

 

 

 

BB

***** Rate All Helpful Responses *****

How to Ask The Cisco Community for Help

OK, clearly. Thanks so much
Ticket can solve.
Getting Started

Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: