I use the free ssh program mRemoteNG to use a manger for the putty program.What do that have that is free and close to putty and putty mangers software for MacOS
Forum Posts
I'm trying to connect a Trunk port using fiber from a 3850 switch to a server using fiber. the following is how i configured the port and the port-channel group:description ntnx 1-3switchport trunk allowed vlan xxswitchport mode trunkswitchport tru...
I have a cloud provider that I need to allow access to a specific port through my firewall. as of now I have had to add every one of their IP Addresses as a network object, and then group them so I could provide access through the firewall in my acce...
HiTrying to configure mdt on asr9010 with rsp880 and xr 7.11.2. Dial out, grpc, no tls.Session Displays na. Paths are resolved. Source in default vrf. Destination too.Same identical config works on c8712 with 25.3.1 and sends data to telegraf.What am...
Somehow, my On-Prem SSM will not let me log into the CLI via any route I try - SecureCRT SSH, vCenter console, Windows Powershell SSH, etc. It tells me logon incorrect. BUT, the WebGUI operates fine with the local admin password. Being that I am r...
Resolved! DHCP Special Configuration
I need some help guys! So we are tasked to figure out DHCP as a school work, and the first part is the DHCP standard. So here comes the next part, as you can see in Networks 1 and 2, they are connected and have DHCP service at Server 1. So the task t...
According to this article, I can delete the current startup configuration files and return the router to its factory default settings with the `erase nvram:` and `reload` command.https://www.oreilly.com/library/view/cisco-ios-cookbook/0596527225/ch01...
I am trying to connect to GUI interface of WLC but it is continuously showing "Server Reset Connection". I configured the management interface of WLC with an IP 192.168.10.10 and PC connecting with the WLC with an IP 192.168.10.11. The PC and WLC are...
Dear Expert, My NMS showing Discard rate for interface gig 1/0/2 is 9%, threshold is 5% and this generates a huge alarms in the system. I want to increase the discard rate to 10% to reduce the alarms but need to understand the calculation or formul...
Hi dear Cisco Community Members I'm about to add a Cisco Firepower 2130 firewall with an ASA image, version 9.14, to a Nagios-based network manager. Could you please tell me where I can download the MIBs to monitor the Cisco Firepower 2130 firewall w...
Hi all,I'm a sound manager in a theater and since about one year I'm moving the audio system I'm working with from analog to full digital. We are now using Audinate Dante system which, you may know, is using audio over IP.Initially I bought 2 Cisco S...
I am using a Cisco nexus 400 GB spine switch to connect to my Cisco N9k C93240YC-FX2 uplink ports. i have set up the breakout to 4 lanes of 100GB but am unable bring up the links. Does anyone know if the C93240 only supports NRZ modulated 4x25g or ...
I need a quick design validation.In our network design, the VoIP Core system (Hybrid PBX + VoIP server) is placed in a DMZ VLAN. All internal SIP phones and voice-related servers sit in the core LAN. This means all SIP signalling and RTP flows must t...
Hello So currently I have a DSL MODEM - FPR1010 - SG350XG. My Internet is DSL w/ 8 static IP's and the FPR does the PPPoE and is connected to the SG350XG with routing back towards the Internet... On the SG350XG I have 6 vlans [each single vlan is a...
A Windows 11 host 24H2 with active 802.1x on the LAN, installed VMWare Workstation and VMs that use the host LAN adapter in bridge mode responds to EAP packets from the switch that are sent to the MAC address of the VM. Why? As a result, the host its...
