07-25-2018 09:52 PM
HI Genius,
Can anyone confirm that XRv900 will support the netflow? I am not able to configure the flow under the interface?
Pls suggest.
07-26-2018 12:12 AM
According to the data sheet is seem to do so :
M.
07-26-2018 01:21 AM
Hi Merce,
Thanks for support
But i could not able to configure the flow under the interface. Pls refer the below mentioned log and suggest.
config details:
=============
RP/0/RP0/CPU0:ios#sh run flow exporter-map
Thu Jul 26 08:18:33.690 UTC
flow exporter-map MPLS
version ipfix
options interface-table
options vrf-table
options sampler-table
!
transport udp 2055
source Loopback0
destination 100.65.212.9
!
RP/0/RP0/CPU0:Jul 26 08:18:39.103 : parser[264]: %MGBL-LIBPARSER-3-ERR_DLL_UNKNOWN_FUNC : Failed to locate function: netflow_pd_perf_traffic_supported in DLL 'libnf_pd_verify.dll'
RP/0/RP0/CPU0:ios#sh run flow monitor-map
Thu Jul 26 08:18:39.940 UTC
flow monitor-map MPLS
record datalinksectiondump
exporter MPLS
!
RP/0/RP0/CPU0:ios#sh run sampler-map
Thu Jul 26 08:18:46.812 UTC
sampler-map MPLS
random 1 out-of 1
!
RP/0/RP0/CPU0:ios#show ospf neighbor
Thu Jul 26 08:18:54.398 UTC
* Indicates MADJ interface
# Indicates Neighbor awaiting BFD session up
Neighbors for OSPF 1
Neighbor ID Pri State Dead Time Address Interface
10.10.50.6 1 FULL/ - 00:00:32 10.10.60.37 GigabitEthernet0/0/0/0
Neighbor is up for 16:01:52
Total neighbor count: 1
RP/0/RP0/CPU0:ios#conf t
Thu Jul 26 08:18:56.666 UTC
int RP/0/RP0/CPU0:ios(config)#int GigabitEthernet0/0/0/0
RP/0/RP0/CPU0:ios(config-if)#flow ?
bidirectional Enable both sending and receiving of flow control pause frames
egress Enable the receiving of flow control pause frames
ingress Enable the sending of flow control pause frames
RP/0/RP0/CPU0:ios(config-if)#flow egress ?
<cr>
RP/0/RP0/CPU0:ios(config-if)#flow egress
RP/0/RP0/CPU0:ios(config-if)#flow-control ?
bidirectional Enable both sending and receiving of flow control pause frames
egress Enable the receiving of flow control pause frames
ingress Enable the sending of flow control pause frames
RP/0/RP0/CPU0:ios(config-if)#flow-control egress ?
<cr>
RP/0/RP0/CPU0:ios(config-if)#flow-control egress
RP/0/RP0/CPU0:ios(config-if)#show platfo
^
% Invalid input detected at '^' marker.
RP/0/RP0/CPU0:ios(config-if)#do show platform
Thu Jul 26 08:19:30.263 UTC
Node Type State Config state
--------------------------------------------------------------------------------
0/0/CPU0 R-IOSXRV9000-LC-C IOS XR RUN NSHUT
0/RP0/CPU0 R-IOSXRV9000-RP-C(Active) IOS XR RUN NSHUT
RP/0/RP0/CPU0:ios(config-if)#
07-26-2018 05:28 AM
- I am worried about the first exotic error message; could be a software bug ; possibly apply more recent software releases on your device.
M.
07-30-2018 11:25 PM
Hi Merce,
I am using the version 6.2.3. Can you pls suggest which version will support the netflow.
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide