07-25-2018 09:52 PM
HI Genius,
Can anyone confirm that XRv900 will support the netflow? I am not able to configure the flow under the interface?
Pls suggest.
07-26-2018 12:12 AM
According to the data sheet is seem to do so :
M.
07-26-2018 01:21 AM
Hi Merce,
Thanks for support
But i could not able to configure the flow under the interface. Pls refer the below mentioned log and suggest.
config details:
=============
RP/0/RP0/CPU0:ios#sh run flow exporter-map
Thu Jul 26 08:18:33.690 UTC
flow exporter-map MPLS
version ipfix
options interface-table
options vrf-table
options sampler-table
!
transport udp 2055
source Loopback0
destination 100.65.212.9
!
RP/0/RP0/CPU0:Jul 26 08:18:39.103 : parser[264]: %MGBL-LIBPARSER-3-ERR_DLL_UNKNOWN_FUNC : Failed to locate function: netflow_pd_perf_traffic_supported in DLL 'libnf_pd_verify.dll'
RP/0/RP0/CPU0:ios#sh run flow monitor-map
Thu Jul 26 08:18:39.940 UTC
flow monitor-map MPLS
record datalinksectiondump
exporter MPLS
!
RP/0/RP0/CPU0:ios#sh run sampler-map
Thu Jul 26 08:18:46.812 UTC
sampler-map MPLS
random 1 out-of 1
!
RP/0/RP0/CPU0:ios#show ospf neighbor
Thu Jul 26 08:18:54.398 UTC
* Indicates MADJ interface
# Indicates Neighbor awaiting BFD session up
Neighbors for OSPF 1
Neighbor ID Pri State Dead Time Address Interface
10.10.50.6 1 FULL/ - 00:00:32 10.10.60.37 GigabitEthernet0/0/0/0
Neighbor is up for 16:01:52
Total neighbor count: 1
RP/0/RP0/CPU0:ios#conf t
Thu Jul 26 08:18:56.666 UTC
int RP/0/RP0/CPU0:ios(config)#int GigabitEthernet0/0/0/0
RP/0/RP0/CPU0:ios(config-if)#flow ?
bidirectional Enable both sending and receiving of flow control pause frames
egress Enable the receiving of flow control pause frames
ingress Enable the sending of flow control pause frames
RP/0/RP0/CPU0:ios(config-if)#flow egress ?
<cr>
RP/0/RP0/CPU0:ios(config-if)#flow egress
RP/0/RP0/CPU0:ios(config-if)#flow-control ?
bidirectional Enable both sending and receiving of flow control pause frames
egress Enable the receiving of flow control pause frames
ingress Enable the sending of flow control pause frames
RP/0/RP0/CPU0:ios(config-if)#flow-control egress ?
<cr>
RP/0/RP0/CPU0:ios(config-if)#flow-control egress
RP/0/RP0/CPU0:ios(config-if)#show platfo
^
% Invalid input detected at '^' marker.
RP/0/RP0/CPU0:ios(config-if)#do show platform
Thu Jul 26 08:19:30.263 UTC
Node Type State Config state
--------------------------------------------------------------------------------
0/0/CPU0 R-IOSXRV9000-LC-C IOS XR RUN NSHUT
0/RP0/CPU0 R-IOSXRV9000-RP-C(Active) IOS XR RUN NSHUT
RP/0/RP0/CPU0:ios(config-if)#
07-26-2018 05:28 AM
- I am worried about the first exotic error message; could be a software bug ; possibly apply more recent software releases on your device.
M.
07-30-2018 11:25 PM
Hi Merce,
I am using the version 6.2.3. Can you pls suggest which version will support the netflow.
Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: