Dear All, I have configured my FTD 6.2.3 through FDM with base, threat and malware license and all the policies are working fine. But today when i open the FDM it says license are out of compliance what causing the issue.??? please help.....
Forum Posts
Hi, In FMC, you can go to Overview --> Connections Summary --> Traffic TAB and there you will see traffic by initiator IP. I would like to get this table but then for a specific IP subnet. I tried to add new search objects under Analysis --> Sea...
Hi, Note: posted elsewhere in another thread. I'm trying to use a searchable syslog server to track the flows on one of my ASAs but have run into a problem. Hypothetically, let's say I have a web server behind an ASA with IP address 192.168.1.1 ...
Hi, I'm working to replace my current ASA5512-X with Firepower services with Firepower 2110 series, and I have Cisco Anyconnect license and Firepower subscription for three years can these be transferred? Or I have to purchase again?
We have an ASA 5506-X at a remote site. A few days ago we noticed from out monitoring (PRTG) that the HTTPS/SSL sensors had failed. Then we found that we were unable to get onto the ASA via HTTPS/ASDM. PRTG is telling us "Failed to establish secure c...
Hi everyone this the first time for me to configure ASA5506-X in cli andi want to configure EZVPN client mode in this device i have 2 questions: 1- when i did (sh running configuration & sh crypto ca certificates )why i couldn't find any certificati...
Hello Everyone, I'm planning an ASA hardware migration from a ASA 5510-K8 v9.1(7)23, ADSM v7.5(2)153 to a ASA 5516-FPWR-K9 v9.8(2), ADSM v7.8(2), FirePOWER v6.2.2-81. I'm pretty new to the ASAs and I would like to get your help/advise for a migrati...
Resolved! Default Routs for ASA Firewall
Question on Default Routes:I have an ASA 5506-X connected to an inside LAN network, and the outside interface will be connected to an ISP.For the default route, should it be the ISP's next hop that I point to? For example:route outside 0 0 x.x.x.xWh...
Hello All, Is there any way that I can Limit administrative access to specific FTDs/ASAs through FMC for a specific user ? Lets say I have 10 Sensors in the FMC but I want to give access to only 1 specific Sensor to a user to administer. Subru...
Hi, Today I noticed that Firepower sometimes working and sometimes it doesnt record any logs for connection events!!for example today I checked connection events from 07:00 AM to 09:00 and I can see the logs started only from 08:49 AM I have upgraded...
Hello Team We have an ASA running FTD 6.2.3 and managed via FDM . Recently i installed the SRU, VDB and GEO updates manually via the Firepower CLI of the firewall. The install of each .sh file completed successfully. I have also verified in the /va...
Hi, Im trying to find the MIB SNMP for FTD 8140 and 8350 but i can not find in cisco download. Please, can you tell me where i can find the MIB fo these models??? thanks
Hi there, I have recently updated ASA to 9.10(1) and ASDM to 7.10(1) on a 5512-X with FirePOWER Services.Following the update I noticed that the FirePOWER tab in ASDM was missing. Also, in FireSIGHT management center, I got a Appliance Heartbeat noti...
Dear All, I am using FTD 6.2.3 and managing it through firepower defense manager. The problem i am getting is that when i enable identity policy users are getting "your connection is not private" on the web browser but as i disable identity policy us...
Hi Does cisco Asa firepower supports url filtering and traffic rate limiting ?Thanks
