Hello everyone, I have a problem with my ASA5516, it does not filter the communications via URL FILTERING, in the logs I can see only the default policy (trust all traffic), I have the license URL FILTERING enabled, and the access policy enabled, I d...
Forum Posts
Any product available in Cisco to detect data leakage?
Hello, maybe I am not in the right place to ask this questions, but I need some help. So, the deal is, I have certain network, in packet tracer, with 'cloud-PT (Internet)' to router, and servers, connected to 1 switch, then goes 'ASA', and from thi...
Resolved! ASA 5525 update
Hi guys. I need your help. We have 2 asa, fmc, asdm. Tried to install last software updates (6.2.3), everything went good except one asa. FMC, first ASA updated successfully. But on second asa it doesnt pass readiness check. Currently it's version is...
Resolved! ASA nat based on destination port
Hello, I would like to be able to pat a device based on the destination port. For example: 10.10.10.49 (any source any destination) ---- 10.10.10.50 (asa) ----- PAT to ----- 222.222.222.222 But also be able to do this: 10.10.10.49 (any source, desti...
I've created a Geolocation list of countries I want to block. Do I put it in my Access Control list as the destination network, source network, or both? If I put the geo list in both, does the FMC interpret it as an AND operator? Meaning the tra...
Resolved! not able to ping device behind
Hi Guys, Just need your assistance on this. I'm trying to setup a GNS3 lab. Attached is the diagram. For some reason, I'm cannot ping the devices behind the firewall. Here are the FW config. FW1# sh run natnat (INSIDE,WAN0) source dynamic any ...
Resolved! Add an FTD to FMC - config import?
Hi, I have an ASA5508-X running FTD 6.2.2-81 which has just gone into production, but I'd like to add an FMC virtual appliance to the environment to control the firewall. When I register the FTD to the FMC, will the on-box configuration be imported...
Resolved! ASA 5555-X Management Interface
would it possible to configure the management interface on the 5555-x with an IP address and also set the interface IP as the default gateway of the Firepower? I am out of available interface on the 5555-x, some cisco doc says its possible, but I w...
Hi Recently we had issue in Microsoft Office communicator, users were not able to share their desktops however the ports are enabled. A microsoft has said that this Cipher suit is normally blocked in firewall and we have to enable ...
I need to replace the primary 5516 ASA but am confused when it comes to getting the configuration written over to it. I configured the failover interface but I am wondering how to get all configurations written from the secondary (which would be the ...
Hi Im upgrading my FMC FS-2000 from 6.2.2 to 6.2.3, from the documents it should take about 40mins. Its now been running for 2 hours. The last thing i can see in status.log from CLI is:ui:[10%] Running script 000_start/400_run_troubleshoot.sh... ...
Hi We want to try out ASAv Qcow image on KVM on a OpenStack LAB environment.Even if we are registered partners, I can not download the Qcow image from the download section. Is there any way to get a evaluation download of the ASAv ? RegardsKjetil
im shifting from a old asa 5510 to a 5516-X with FTD and i need to add websense server url filtering as shown in the below image to it but i cant seem to find where to configure it on FTD exactly?
I have an issue where I am using postman to hit the FMC's API to update an existing Network Group. Postman works. I have taken most of my Postman calls and translated them into UCS Director Javascript calls. I can log into the FMC, I can determine...
| User | Count |
|---|---|
| 10 | |
| 7 | |
| 5 | |
| 2 | |
| 1 |
