Hi: I have an SA540. We changed ISPs so I updated the WAN settings. Now remote management will not connect. If I try to telnet to the public IP from outside on port 443 it won't connect. Remote management used to work w/old ISP WAN IP and I did...
Forum Posts
Hello, We have a dedicated and synchronous 75Mbps internet link on the outside of an ASA5545 Firewall. version 9.8(2), I want to control this rate, as a lot of people from the inside are heavily consuming the bandwidth.I want to customize 60Mbps for...
Hi, I keep receiving log messages on ASA 5545X like this: 2 Apr 06 2018 07:47:57 19.19.20.4 19.19.20.4 Deny IP due to Land Attack from 19.19.20.4 to 19.19.20.4 This is for server - IP which is 1-to-1 NAT 10.1.4.4 ->19.19.20...
Dear Team, We have to replace Juniper EX4200 & EX4500 switches by Cisco Nexus 2000 and Nexus 5000 series. is there any migration tools that we have to use any for migration? Thanks in advance. Regards, Chirag
HiToday I upgraded my Cisco ASA 5505 ASDM from version 6.34 to 6.41 cause of some problems on old version with NetFlow.But now when I switch to dashboard i can not see "Top Usage" tab. That was quite usefull for me. It simply disappeared.Can i someho...
Dears, I have here 2 queries: I get the attached error while saving the configuration in the ACP and also while configuring the active authentication, I am dong PBR for the the internet traffic 80,443,53 to my next hop that is adsl router and res...
I keep reading that the protection license is included with the firepower module. So how do I find and activate the license if I don't care about updates? I own a 5506X for home for studying purposes mostly, but also as an edge firewall and VPN. I...
Resolved! ASA5515-IPS Renewal
Hi, I'm wondering why i couldnt find a correct SKU to renew my ASA5515-IPS it seems like there is no SKU for IPS only. My show version : Cisco Adaptive Security Appliance Software Version 9.2(4)14 Device Manager Version 7.5(2)153 Compiled on Thu 1...
Hi All, We recently purchase Firepower 2120 with ASA Code 9.9.1. We managed to setup the AnyConnect and can be connected from internet. When we try to host a public server. We have the access rules and NAT in place. Just that from the log, it alway...
I did search "ASA throughput" here on the support community and read through 20 something posts about it, but I still am confused and have a question. Not talking about any model in particular, imagine in terms of throughput, a 400Mbps max for multi-...
Not sure why the ASA is not allowing me to create a new Access Control Policy and any help would be appreciated. Updated the Sourcefire from 5.4.1 to 6.0.1-29 and now I cannot see where the create a new policy has disappeared to. Logon to the ASDM ...
I am trying to change from UDP to TCP for syslogging on my 5585-X, version 9.6(4)3. I am using the management interface, for which I have turned off "management only", and I also turned off management access. However, the packets go out, but return...
Hello We have an urgent situation to try and get our Cisco Firewalls/Firepower devices up to the latest 6.2.2.x version. We currently have the following environment with devices running in HA (Active-Standby) so 2 devices of each below. Firepow...
Hi everybodyI want know why create whitelist ip add in IPS? And if IP of the packet belong to whitelist ip addr that content check in IPS section?or traffic send to IPS?
I am trying to get a demo going for a next gen firewall & found the link below saying that I can install FTD software on an ASA5500-X series device. I am trying to avoid running ASA with Firepower Services & I want to get FTD directly on the ASA. The...
