I have updated FMC to version 7.6.2. I’m wondering, since my FTD is currently running version 7.4.2.2 — should I first upgrade the FTD to 7.6.2 and then patch FMC to 7.6.2.1?Or, can I patch FMC to 7.6.2.1 right away and then upgrade the FTD to 7.6.2 ...
hi,i encountered a strange issue with my ASA primary FW. i can't login via TACACS+ on the primary but i can login fine to the secondary ASA. ping to ISE/TACACS+ server from both primary and secondary ASA are fine. i'm only able to login to primary AS...
Hello everybody, I have been tasked to install the BIOS Update HotFix FC 7.4.99.99-1 on a FMC 1600 running rel. 7.4.2.1.I have never done this before and did not find a step-by-step guide. My questions:1. Is there a guide for this task?2. Is it neces...
Hi Team, We have an FTD which have an inside interface connect to our LAN switch, this interface is segregated through subinterfaces for DATA and AUDIOCODE vlan and both come under same security zone as seen below.We have both policy and nat rule for...
Hi everyone, Our Firepower 1120 device shows a blinking amber light on the power LED when powered on, while all other LEDs remain off. In addition, we are unable to access the console screen. We have attached a video showing the current behavior of t...
We are currently using FMC and ISE to manage admins who can log into FMC and the firewalls in our environment. We were considering how we can better secure our management connections, specifically the communications between our firewalls and ISE. Cur...
Hello All,Would like to know if there is a way to configure HA between 2 Cisco 1010 FTD using Device Manager? I was trying but the HA Configure button is greyed out due to error stating I need all interfaces to have a static IP address. I am looking ...
Hello Cisco Community!We have a situation where we need to disable SQLNET Inspection in the FMC Cisco Firepower 2110 Threat Defense.I would appreciate your guidance on how to do this using the GUI and the command line.I found the information about...
I’m designing a multi-branch network using Cisco Secure Firewall 1220CX appliances at each branch, connected to Catalyst 1300 switches for local access. Meraki APs connect to the switches.The goal is to achieve centralized, cloud-based management fo...
Hello,FTD 2110s 7.4.2.4I'm looking for suggestions on two topics. 1. What's the best way to help prevent Dos attacks to the FTD itself. Is flex config the only way and does anyone have a proven config. for that they could share?2. What upstream servi...
Hi AllI will be adding another FTD into our CDO platform, however the licence for the new unit sits in a different virtual smart account than the current one.Do I just click on claim subscription ? how would I link the licence in this other smart acc...
Hello everyone,we are using the Cisco ASDM-IDM Launcher v1.9(9). When the Launcher connects to a system with a self-signed SSL certificate, we do not receive any warning messages. Additionally, I cannot view or verify the SSL state in the Cisco ASDM-...
Hi,When looking at a host profile discovered by the network discovery policy in FMC I see there is a "Servers" section with the list of protocols and ports listed according to the connection events registered for this host as a destination. Down bel...
Greetings everyone, I’m writing to you out of sheer desperation, but I’ll give it a try anyway—maybe the collective intelligence here can help: I’m trying to set up a site-to-site VPN between an on-premise network and an Oracle Cloud Infrastructure (...
Hello everyone,I'm having trouble registering my FMC with Smart Licensing because it's on a segmented network with no direct internet access. I've added a secondary NIC (eth1) with internet connectivity, but I cannot find in the FMC's any interface ...
