In current configuration, there are no security zones configures as of now.
In current configuration, there are no security zones configures as of now.
1, FSMC show 2 critical health errors for SFR & Sourcefire3D related to time synchronisation. - Module Time Sync is out2. Also showing -Health monitoring severely behind schedule error in health. Any ideas on this issue . How I can resolv the issue?
Hi, If i wanted to install on ASA Software on 41xx Chassis, what license we require? as far as i know, we can't Install FTD if we install ASA SW, so we don't need FMC to manage the Firewall? will also the old ASA CLI be available or do we need to In...
1. Can share if SourceFire have support coverage in these countries?2. What SLA are available?3. Can we engage the remote service to help reconfigure back to last config and so as that we can remote via internet for any further setu...
hello,i have Cisco c 160 ( version 8.0.1-023),i want to realse mail from spam quarantine,when i select monitor>spam quarantine >press on the number of the mail ,the new windows open but with "canot display the webpage" ,these way i can't release mai...
I'm having a hard time "tracing" how ACL's on subinterfaces on a Cisco ASA work. Let's create a simple scenario:- ASA Gi0/0: trunk to SW01 Gi0/0- ASA Gi0/0.10: VLAN10 subinterface- ASA Gi0/0.20: VLAN20 subinterface- SW01 has both VLAN's and Gi0/0 con...
Hello everyone, I am in the process of upgrading the flash via EUSB on one of ISR 4331 routers. Does anyone have any experience performing this upgrade and can provide detailed instructions for upgrading the EUSB. I have researched Cisco's site...
hi all, I have pair of 4110 in another site accessed via VPN.is there any port or specific protocol that should be allowed on VPN so FMC can communicate with the FW? the FW registers, it goes through discovery and de registers on FMC due to communic...
If someone could please help, I would appreciate it. This tunnel reports up (via show vpn-sessiondb l2l). But no traffic will pass. Seems to get denied at Phase 2. Something wrong with ACL it says. I'm not seeing. Wizard wrote the config includ...
I have a very simple configuration; however, the two same security level interfaces cannot talk to each other. I have had a TAC case open for 2+ weeks and I’m at the point of frustration. Should I blow the configuration away and try again? Everythi...
Hi networkers,I recently run a pentest against a 2911 router. It mentioned the following message:[quote]Vulnerability allows remote attackers to force the downgrade to an unintended cipher. OpenSSL before 0.9.8q, and 1.0.x before 1.0.0c, when SSL_O...
Hi Team, I just configured an ASA 5516 at one of our client's office, It is below the edge router (not directly connected to the internet). I created three zones (LAN, OUTSIDE AND SERVERS). The OUTSIDE interface is connected to the edge router and t...
Hi Guys, Good Day! I am a bit new in Firepower, may I know how does FP do hardware HA, is it like ASA? We can have Active/Standby and all configurations should be only on Active appliance? What FP monitors to trigger the failover? Thanks
Join Foster Lipkey, Cisco Technical Leader within the Technical Assistance Center (TAC), as he walks you through several advanced troubleshooting scenarios with FTD.Choose one session to attend (content same for both).August 24th at 10AM PTAugust 31s...
Join Foster Lipkey, Cisco Technical Leader within the Technical Assistance Center (TAC), as he walks you through several advanced troubleshooting scenarios with FTD.Choose one session to attend (content same for both).August 24th at 10AM PTAugust 31s...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
07-16-2025 04:21 AM | ||
07-06-2025 01:40 PM | ||
07-04-2025 01:59 AM | ||
06-19-2025 07:32 AM | ||
06-17-2025 01:07 PM |
User | Count |
---|---|
10 | |
7 | |
5 | |
1 | |
1 |