Please see attached for diagram of what I need to do. This is ALL internal. The Firewall is a ASA 5525-X and connect to a private switch on the outside. I need for users to connect through this firewall to the lab. Do I need NAT for this?
Hi guys, We have a scenario where we've inherited a client with the above mentioned device, inherited a VPN issue with a particular user. None of us here are particularly versed with the Cisco ASDM 6.4 console so would like guidance. The symptom: W...
Can't figure out why this L2L VPN is being denied. "show crypto isa sa" returns "There are no IKEv1 SAs". running ver 8.4(5). What am I missing? ASA-5510# sh run: Saved:ASA Version 8.4(5)!hostname ASA-5510names!interface Ethernet0/0 nameif outside ...
Hi all, I have a VPN between 2 sites between 2 routers, in my LAN i have a router and firewall ASA, what i should configure between ASA and Router in my LAN ? my archetecture as following: thanks in advance, Regards, MM
Hi, I can’t seem to get the below to work, so hopefully someone can help. The ASA has 4 live interfaces as below. 1. Outside (security 0) 2. Inside (one sub interface, security 100) - inside_11_infrastructure - - PAT’d to the outside interface (wo...
Hi All Hoping someone might be able to help us. We use a Cisco ASA5516 ASA version 9.6(2) and noticed some odd results while monitoring network traffic which we can't explain. We have around 10 remote offices that connect back to head office through ...
Hi All,I have 2 ISP terminating on the ASA5585 version 9.4 Incoming NAT-TrafficI need to have both the Email and Lync servers NATted to public IP and both accessible at the same time.Is that possible in my setup? Outgoing TrafficInternet traffic defa...
Hello, I have configured my ASA, any configuration changes it should be logged into my Kiwi Syslog server. when I do any config-changes on my ASA through CLI then it is logging onto my syslog server, but whatever config-changes I do through ASDM ...
Hi Guys,I have a problem with my new Cisco Security Manager. I installed the server on a Microsoft Server 2008 R2 Standard SP1. The Software was installed on Drive E:Now I want to change the admin password which was set during the installation. I fou...
Hello everyone I didn't see any "Licensing" category in this forum so I'll just ask here since my question is - in the end - regarding a 5506-X. So, since AnyConnect might come fairly soon to the FTD image, I am planing the migration of my personal ...
Hello, (ASA5505, running 9.2.1) I have a requirement from one of my software vendors that has an external portion to their service to limit incoming traffic on the port they need to a specific public IP address (for security, only allowing the incom...
hi, please any one help me to configure website filtering in Cisco 1841 router. Regards, Abhijith
Is there any way to do a automated schedule backup of config to external server via tftp or ftp?
Hi, from last week, I am having problems with skype. I am unable to hear voice when I make calls with skype. for skype to work I need to have: All destination ports above 1024 (recommended) or Ports 80 and 443 all port above 1024 are not open. b...
Have 3 Sensors 2 x in one country (protection and control license) and 1 ( Protection, control and URL Filtering) in another country (*) I have created a separate IPS and Access Control Policy for the 2 first sensors and then another IPS and Access ...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
| Subject | Author | Posted |
|---|---|---|
| 05-05-2026 09:59 AM | ||
| 05-02-2026 06:09 AM | ||
| 04-30-2026 12:46 AM | ||
| 04-24-2026 07:04 AM | ||
| 04-22-2026 11:56 AM |
| User | Count |
|---|---|
| 6 | |
| 3 | |
| 1 | |
| 1 | |
| 1 |
