Under Management portalAfter adding a few bits (Ports, Networks + Group and Policy) the deployment failed. I tried to add ports 9443 and 6443, but this also led to failed deployment. I am lost on why the failure is happening on small changes too.
Under Management portalAfter adding a few bits (Ports, Networks + Group and Policy) the deployment failed. I tried to add ports 9443 and 6443, but this also led to failed deployment. I am lost on why the failure is happening on small changes too.
Hi All,We've been seeing mysterious reboots of FPR2140 running 7.2.4, so logged a TAC case.According to TAC we were hitting the following defects.https://bst.cloudapps.cisco.com/bugsearch/bug/CSCwh10681 [bst.cloudapps.cisco.com]https://bst.cloudapps....
I would like to install the new cisco secure client 5.1.4-74, which will auto update when remote users log in. However I would only like to install the vpn client, and not the rest of the msi's that are loaded in the cisco-secure-client-win-5.1.4.74-...
I am not sure if this is possible, but I can't get it to work.We recently setup an IPSEC/VTI VPN with 'vendor A'. That tunnel and VTI interface are up. Routes are being exchanged via BGP. The VPN was setup on a Cisco ASA. The ASA has 2 VPN's to 'vend...
Hi all, I've had a problem for a while with my FMC.In fact, there was a DNS problem on my network and I have since found that all the policies I apply on the Cisco FMC do not deploy on the FTDs. I keep getting the following error:Timed out collecting...
Hello wonderful people,do you know of any tool that can convert ASA NAT details (sh nat details) in a tabular format for better visibility? something like this as an example (see table below).there are tons of lines of code and its will be super over...
Hi,I bought a Firepower 1010 NGFW for a small office and it does route traffic generally to the internet I can't seem to get the Geolocation, VDB, Security Intelligence Feeds, Intrusion Rule. NTP doesn't update either but is set to use (0.sourcefire...
Have two HA clustered FTD2130's managed by FMC and I am unable to upgrade the FTD's past 7.2.1FMC currently running 7.3.1.1FTD's running 7.2.1...trying to get them up to 7.3.1; All policies on the FTD's are up to date.FTD's working normally in a HA c...
A security auditor has requested we show how our FMC/FTD security devices comply with the following two controls. What can I show them to satisfy these requirements?TIA,SC-5: Denial of Service Protection:The information system protects against or li...
Hi, I have upgraded my FMCv and FTD from version 7.0.6.2 to 7.2.0 to finally migrate to 7.2.5. However, I can't jump from FTD version 7.2.0 to 7.2.5 because the readiness check Failed. I realized that the FTD statistics couldn't be shown after the up...
Can someone help to find out mitigation of CVE-2024-20271. as per cisco, there are saying work around is not there and fix to upgrade version. However, the http where this info is updated is saying that vulnerability is affected to AP.For my device,...
How do you go from appliance mode back to platform mode? We are trying to convert our Firepower 2100 to running FTD. We've tried booting in rommon and applying factory-reset and boot, it goes back to loading the ASA in appliance mode. These commands...
Hi all, From the vulnerability scan, we got the below issue for NTP for Cisco 3850 switch. Could somebody please advise how to fix it. An NTP control (mode 6) message with the UNSETTRAP (31) opcode with an unknown association identifier will caus...
I currently have an 1120 running in appliance mode on ver 9.16(1) and need to upgrade due to a vulnerabilty.The current recommended version is 9.18.4.29 (June 2024), although I would be more tempted to go for 9.18.4.24 (May 2024)I cant find any docum...
Hi All,I downloaded the asdm-openjre-7191-90.bin (Cisco Adaptive Security Device Manager for ASA 9.8-9.19 integrated with OpenJRE) BIN file and I have no clue how to execute this.I did some googling and from what I found you need to burn it to a CD a...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
| Subject | Author | Posted |
|---|---|---|
| 05-26-2026 07:54 AM | ||
| 05-02-2026 06:09 AM | ||
| 04-30-2026 12:46 AM | ||
| 04-24-2026 07:04 AM | ||
| 04-22-2026 11:56 AM |