Hi,I think I need to NAT the source and destination of packets and was hoping someone would assist.My firewall is an ASA 5512-x with Internet facing "outside" interface IP address of 1.0.0.1/28 (for this example)I need ALL external Internet hosts to ...
Please correct me if I am wrong. For site-2-site VPN's and client VPN access into the private LAN and from the private LAN to the VPN clients and sites, I do not need to configure No NAT with the newer 9.x ASA software. The older (Pre 8.3) No NAT for...
Hi,I would like to add an another internet provider to my firewall. I have currently AT&T with T1 lines and want to add Verizon or Comcast as backup internet line or divert some of the traffic to new connections.How i could achieve this. basically i ...
HiI donot know if its a right forum to ask this question.Is it possible to view the configuration changes on CCW Config ID. For example I create a configuration on CCW and next day I update the configuration. How can I see what are the changes from p...
Hi,How to setup or what logging server should i use to monitor all vpn client users?I just want to have their details etc.thanks
i want to make sizing for firepower. and i know to make sizing, i must know throughput. i can't measure throughput but i know the number of user.am i able make sizing by number of users?
Hi,I Would like to ask if how can I verify who connected to our VPN?I want to know it's details and date or any??thanks
I have an internal web server I want to NAT to multiple clients coming in over VPN tunnels.The web server is behind the "inside" interface of the firewall, and its real address is 172.25.92.73Another firewall sits northbound from this one, and provid...
Hi,I would like to add an another internet provider to my firewall. I have currently AT&T with T1 lines and want to add Verizon or Comcast as backup internet line or divert some of the traffic to new connections.How i could achieve this. basically i ...
I'm upgrading all of our IPS appliances and started a local upgrade on the first one at 7PM. It's still at 26% running the script 200_pre/500_stop_system.sh... It's been running for over an hour now. Do these upgrades always take this long or am I...
Hi,I would like to add an another internet provider to my firewall. I have currently AT&T with T1 lines and want to add Verizon or Comcast as backup internet line or divert some of the traffic to new connections.How i could achieve this. basically i ...
Hi All,I have a clusted set of ASA 5520's in my data center, and I need to reload the primary unit asap without causing downtime.Is there a way I can fail-over to the standby ASA 5520 in the cluster (with no interruption), issue a command to reload t...
When I try to enable dhcprelay in ASDM I get an error message also when I do it through CLI it lets me put the command in but it doesn't actually take it.Any idea why I'm getting the error?Thanks
Trying to set DHCPRelay so DHCP requests from the inside interface of the ASA are routed to a DHCP server in another site. Get an error message when issuing the configuration command "dhcprelay enable inside" that states the inside interface is alrea...
Recently I installed a Cisco ASA 5512-X, and have successfully set it up for traffic to the outside, and traffic going out from the Exchange server is fine. But incoming traffic and access to the OWA web portal, I cannot get configured so that it wi...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
| Subject | Author | Posted |
|---|---|---|
| 09-22-2026 04:13 PM | ||
| 08-25-2026 06:22 PM | ||
| 08-24-2026 12:26 AM | ||
| 08-20-2026 05:54 AM | ||
| 08-19-2026 07:59 AM |
| User | Count |
|---|---|
| 4 | |
| 1 | |
| 1 | |
| 1 | |
| 1 |
