Resolved! Nat load balancing
Hi I have a cisco ASA firewall (9.1). I have 2 x FTP servers that sit in the DMZ 10.99.1.6010.99.1. 61 I want to NAT them to 193.164.55.20 So when ever an external connection trys to contact my FTP server it will p...
Hi I have a cisco ASA firewall (9.1). I have 2 x FTP servers that sit in the DMZ 10.99.1.6010.99.1. 61 I want to NAT them to 193.164.55.20 So when ever an external connection trys to contact my FTP server it will p...
Hi, I have a question about ASA 5525-X. Can this ASA be used to dynamically PAT one IP subnet of private IP addresses (from inside port to outside port) and in the same time just to route other IP subnet of public IP addresses without PAT?I would hav...
Hi, Any one ran into this issueWe use websense for guest wifi but i dont see requests hitting websense serverconfig is below class-map type inspect match-any test-1 match protocol httppolicy-map type inspect Wifi-test class type inspect test-1 ins...
I am trying to configure an active/standby pair of ASA 5512's running version 8.6(1)2. The standby ASA will not sync with the active ASA. Is there a bug for this or is my configuration lacking?#show running-config failoverfailoverfailover lan unit pr...
Hello, I configured ASA to send email notifications. My exchange server is at the same network as the inside interface of ASA but I do not receive any email alerts. I set it to receive informational email in order to receive something to see if it is...
ASA 5505 IOS ver 9.2.3I need to create a firewall rule that will allow internal services to be accessed externally, but using port forwarding. For example I'd like to enable access to our NAS via ftp external on port 1545 and then have the ASA forwar...
I normally configure the IPS module on a ASA no problem and its pretty standard setup but I came across a Cisco ASA 5515-X 9.1 code running two modules a Cisco IPS without a software image and a Cisco CX not configured with 9.1. Do I need to configur...
I have a few users that are only allowed 3 hours for access to the Internet. It's not my rule, management wants to limit contractors to access the Internet for 3 hours a day. I see where I can do a time rang ACL, like between 8am and 5pm Monday-Frida...
Hello all,I´m setting up a pretty basic lab on GNS3 and I´m getting a weird issue on my DMZ. I have a LAN interface and a DMZ interface, currently both with security-level 50 (lab purposes only), I think I have everything setup but host on both ends ...
I've read through dozens of posts and so far have had no luck getting any of the suggestions to work - combined with many of these posts being multiple years old...so I'm going to try posting something current and see if I get anywhere. Scenario:Site...
Hello All I'm new to the ASA (or firewalls in general) and I'm getting a little stuck with allowing traffic between interfaces. I have two interfaces currently setup and they are used for my inside traffic (connects to a cisco 2611 router) and my wi...
Dear Support, I am having the ASA 5515 and in this ASA CX module install for contain filtering.I have configure the some policy in CX module through PRSM GUI.I also enable ssh for CX module. My CX module is not have any problem all my policies are wo...
version 8.2(5) is presently installed and running fairly well, however, we need to upgrade the code on the firewall to bring it up to spec. when trying to following the upgrade path to 8.4(6) the following errors occur after the reload. Please advise...
Recieved an RMA FWSM and cant console to it. Cisco shipped with OS version 2.3 so cant session into it. Console hangs during bootup. The old FWSM being replaced is hardware verison 3.0 and the new is 4.5.Is there a a requirement for hardware version...
I have having serious issues with performance on my ASA 5505s that I am testing with 9.2.3 code.I stripped the config and removed as much stuff as I could - no VPN etc. and I am ONLY getting about 30-40Mbps downloads from sites but 95Mbps uploads????...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
| Subject | Author | Posted |
|---|---|---|
| 08-20-2026 05:54 AM | ||
| 08-19-2026 07:59 AM | ||
| 08-10-2026 08:58 AM | ||
| 08-10-2026 02:48 AM | ||
| 07-22-2026 05:00 AM |
| User | Count |
|---|---|
| 3 | |
| 2 | |
| 2 | |
| 1 | |
| 1 |