Network Security

Resolved! ASA SNMP

Hi All, Can anyone please advise which of the traps I need to enable if I only need to know fan status. We are running on old version and our aim is to enable snmp traps so as to know if the fan is faulty. Can anyone please advise of the below which ...

PRSM - ASA Active/Standby - Error ASA CX import configuration - Unauthorized request

Hi,I'm trying to add a pair of ASA in HA (Active - Standby) in PRSM Server Multimode Device Mode. I'm getting the error that appears in the title:"Error ASA CX import configuration - Unauthorized request Version ASA: 9.1.3ASA CX: 9.2.1.1 (48)ASA PRSM...

ASA 5505 9.2(1) Port Forward issue

Hello,I could really use some help in setting up a port forward rule on my ASA. I have a host on the LAN (192.168.1.24) I need to expose ports 8082 and 8083 (both tcp and udp) to the Internet. I have an existing rule set up for another host on the LA...

Resolved! ASA inter-vlan routing

Hi, I have this situation:A client of mine has a switched network. On that network where no vlan is configured, he has multiple IP address on the same vlan (vlan 1). So, I´ve installed a 5505 with two vlans, and asigned each vlan to ethernet interfac...

Error importing Active/Passive ASA's into PRSM "ASA's have same CX..."

I have a TAC case open. After first "misplacing" my ticket last week they have been of very little help.ASA 5585 SW Version 9.1(4)CX Modules SW Version 9.2.1.2(77)PRSM SW Version 9.2.1.2(77)The mgmt-plane trace log from PRSM seems to have relevant in...

after upgrading ios Cisco Catalyst 6500 Series Supervisor Engine 2T ASA-SM is disabled

after upgrading ios Cisco Catalyst 6500 Series Supervisor Engine 2T to the latest release the ASA-SM module is not recognized it is disabled. the FPDis not recognized any more. reverted back to previous ios with no luck

Resolved! Routing Question with Cisco ASA 5505 with 2 "Active" WAN Connections

We currently have a Cisco ASA 5505 Security Plus. I am looking to bring in a seperate circuit to handle our SIP trunks. I am not talking about an active/standby or failover setup. Can I achieve this with a simple route statement? Here is some bac...

Cisco ASA + FreeRadius: Downloadable ACL configuration

VPN users that are using FreeRadius are having access to all VLANs. VPN users using local authentication have local ACLs applied to their access. I need to know what configuration change I need to make (on ASA or FreeRadius) to have the same ACLs (lo...

Resolved! 2 internet Connection teminated to ASA 5512

Dear all I have 2 internet line (Leased line and ADSL line ).Now my requirement is In ASA 5512 in the top of network with IPS . I have 6 vlans in the core switch .In 1 Vlan Passing to internet Traffic to normal ADSL Line .and all other Vlans and tra...

PIX 525 / big issue? help please

I've configured 2 pixes, (active / standby) and worked fine for one day then lost one of them,I spent about 8 hours to fix the issue without luck, can I run only one of them? as I have to get the network running within 24 hours (we have a conference ...

How to activate "sla monitor" command in Cisco ASA 5510 ? Please i cannot find this in my ASA console line. Help me out!!

I have two ISPs connections (ISP1 and ISP2). I want to track ISP1 connection and switch ISP2 in case ISP1 connection don't respond. When i want to use sla monitor in privilege mode i cannot see the command. i don't know how to figure out this.

Resolved! Ping from System Conext in Multi context ASA

Hi Everyone,ASA has 2 contexts HR which is admin and other context Sales.When i ssh to HR(admin) and go to system context.Ping works fine from system context to HR context interfaces and also to nei switch which is connected to context HR amd also t...

ASA upgrade- 8.2.2 to 9.0.3- upgrade path?????

Hi,I want to upgrade ASA 5520 from 8.2.2 to 9.0.3.what will be correct and best upgrade path.can we do like this.8.2.2>8.4.6>9.0.3.can any suggest me the best upgrade path or the above listed is the right one.Regards,Vivek

Resolved! Cisco PIX 7.2(2) vulnerabilities

Hello Hope you are doing well, I kindly ask for your help. I have a Cisco PIX Security Appliance Software Version 7.2(2) and I have detected the next vulnerabilities: OUTSCAN detected one medium-risk vulnerability that is related to the Internet Key ...

how can we rate limit (inbound & bound) traffic on a ASA interface

How can we restrict inbound & outbound traffic on a ASA interface to a required limit.

Network Security

Forum Posts

Resolved! ASA SNMP

PRSM - ASA Active/Standby - Error ASA CX import configuration - Unauthorized request

ASA 5505 9.2(1) Port Forward issue

Resolved! ASA inter-vlan routing

Error importing Active/Passive ASA's into PRSM "ASA's have same CX..."

after upgrading ios Cisco Catalyst 6500 Series Supervisor Engine 2T ASA-SM is disabled

Resolved! Routing Question with Cisco ASA 5505 with 2 "Active" WAN Connections

Cisco ASA + FreeRadius: Downloadable ACL configuration

Resolved! 2 internet Connection teminated to ASA 5512

PIX 525 / big issue? help please

How to activate "sla monitor" command in Cisco ASA 5510 ? Please i cannot find this in my ASA console line. Help me out!!

Resolved! Ping from System Conext in Multi context ASA

ASA upgrade- 8.2.2 to 9.0.3- upgrade path?????

Resolved! Cisco PIX 7.2(2) vulnerabilities

how can we rate limit (inbound & bound) traffic on a ASA interface

On-Demand Webinar: B&M Security Transformation with Cisco XDR

Congratulations to the Event Top Contributors Class of 2024!

Knowledge Hub: Cisco Technology for Securing the Enterprise

Cisco + Splunk: It's a new day for your data.

Announcing Resources That Guide You to Success

Assistance Needed for Cisco ISE 3.2 Lab Authentication with Stealthwat

FTD firewall pair: packet loss on a vlan

ISA 3000 I/O contacts for red light kill switch ?

ERROR(567): No database files are available on Cisco Security Manager

CSSM On-Prem with FTD on FMC

ASA to FTD migration

FDM1120 Management Interface IP Address

OSPF Passive interface in FTDs

FMC displays working IKEv2 tunnel DOWN

FTD 3105: Connot change the gateway (commit-buffer do not work)