Apologies for the naive question but is it possible to load FirePower Services on an (ASA5585-)SSP-IPS20 hardware module? Or is a new hardware module required? Thanks,
Apologies for the naive question but is it possible to load FirePower Services on an (ASA5585-)SSP-IPS20 hardware module? Or is a new hardware module required? Thanks,
Hi any advise on regarding bandwith for ISE nodes (DC & DR)
I am fairly familiar with ASA 8.4+ NAT rules but was wondering what is considered the best practise when an ASA is an Internet edge device that is doing NAT/PAT for Internet access as well as Site-to-Site VPN with RFC1918 addressing on either side of...
I am trying to convert a Juniper to Cisco config, I've used the online tool however I got a lot of errors showing the line that the tool could not convert. I'm working on the below at the moment. is there a way to configure the UUID on an ASA or how ...
Dear Supporter,I need you help me to solve this issue. I have a web-server in my office, I want to access to my web server from outside via domain name, so I have registered with Godady by convert my public ip to www.domain-name.com, after that I can...
I have a rather complex configuration in my office network.Rather compex, of course, from my perspective...I have an ASA 5505 facing the internet through 2 CISCO routers under HSRP between them (10 mbps fiber optics link + copper 4 mbps SHDSL link).O...
Hi i have an ASA firewall configured with VLAN. All this while to configuration was OK and each server (VM) able to ping each other.Then we start to configure NAT in the firewall. Somehow (2 days ago) we realize that there is one server that we can'...
Hi Experts,Please help me on this. I have attached my network diagram with this post.My firewall is cisco ASA 5510 running with software version 8.4. I have configured static NAT for three servers (in diagram, server 1,2 and 3). The issue is, the sta...
I've got 2 ASA 5515-X firewalls that I want to set up in an HA pair. According to this link, the 5515-X is supposed to allow active/active and active/passive failover with the base license. When I run "show activation-key" on either of the units, I...
Hello,I have an IPSEC tunnel to a vendor who I can reach and i see encaps/decaps. When he tries to ping my IP 192.168.26.10 i decap but can't encap. Can any one assist?cleaned up config below. Please let me know if anyone wants to see more.! !interfa...
Hi All,I need to set up a restricted account for some junior's on my ASA's, so I have built the following:aaa authorization command LOCALprivilege show level 3 mode exec command vpn-sessiondb l2lprivilege show level 3 mode exec command crypto isakmp ...
We have an ASA 5510 with 3 connections, outside, inside and point2point running version 8.2 without nat control. We need hosts on the inside interface to communicate to hosts on the point2point interface. When we use the same-security-traffic permit ...
We are getting a new internet circuit with a new block of addresses. How do I quickly update my access lists with the new public ip address? Any help would be appreciated. Thanks
Hello,I have changed out the CCO username and password for an IPS configured for auto-update but cannot get the IPS to correctly update its signature any longer. I have verified that the CCO login is correct and that it can download a signature file...
Hello all,I have a Cisco 2901 router running 15.3 (M3) that I am trying to setup a basic firewall on. I want to remote console into computers from only certain IP addresses. I've created the objects and rules below and applied then to the subinte...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
| Subject | Author | Posted |
|---|---|---|
| 05-05-2026 09:59 AM | ||
| 05-02-2026 06:09 AM | ||
| 04-30-2026 12:46 AM | ||
| 04-24-2026 07:04 AM | ||
| 04-22-2026 11:56 AM |
| User | Count |
|---|---|
| 6 | |
| 2 | |
| 1 | |
| 1 | |
| 1 |