Hello,May I know if any thing else is required apart from below, if DC MGMT and the sensor appliance management are on a separate network separated by a firewall.443 (inbound) and 8305 (inbound and outbound)Regards,Akhtar
Hello,May I know if any thing else is required apart from below, if DC MGMT and the sensor appliance management are on a separate network separated by a firewall.443 (inbound) and 8305 (inbound and outbound)Regards,Akhtar
Hi, I was trying to configure a DMZ on our firewall for a webserver.Our topology is ... Internet > Router 3925 > ASA5525 > Switch(inside LAN)I have an interface on the ASA connected to the DMZ switch. ASA5525 > DMZ switch > Web server. The ACEs for...
I've created a couple of patches for the Host Input API and the Tenable SecurityCenter Input Plugin that I would like to contribute back to trunk. What is the process for submitting the patches? Thanks! --Matt
Hi Am getting below error while am try to copy image from ftp server. aaaaaa# copy flash:flash:/asa821-k8.bin ftpSource filename [/flash:/asa821-k8.bin]? asa821-k8.binAddress or name of remote host []? xxxxxxDestination filename [asa821-k8.bin]?Writi...
Hi community, On Cisco Routers you have the option to configure multiple SSH ports (instead of the default tcp 22) in combination with rotary groups. Then, attach these rotary groups to specific VTY lines.This works just fine. But, it seems on Cisco ...
Hello,our company is currently in the process of buying a new firewall and the ASA 5515-X seems like a good choice for us, but I have two questions regarding it. 1. Do you have to buy a separate license for using a failover configuration or is one al...
Hi..I have been running IPSec RA VPN on ASA at my one location, i have recently setup a new location with new another ASA configured with IPSec RA VPN. I have configured same VPN group name on this new ASA.I have been seeing a strange behaviour whic...
Hello,I am new to ASA. I have set up a lab in GNS3.I cannot ping the outside interface from inside or vice versa. I have tried adding ACL's, inspect icmp and everything that I found while searching for the solution.My Current running config is:ciscoa...
Hi,we want to deploy four firewalls in cluster in individual interfaces mode. Because we are using individual interfaces mode each interface will have a different IP address.As the site-to-site VPN is a non-cluster feature, VPN traffic will only be ...
Hello Support, We have two locations which each have an ASA. See attached for models. There are VOIP phones at Office 2, and basically all calls from the phone device 172.30.30.10 route through the phone device 192.168.8.10. The idea behind this desi...
What NGFW features can be enabled if I purchase the ASA5515-x (ASA5515-SSD120-K9) and 3 year license of AVC, WSE, and IPS (ASA5515AWI3Y)? I was under impression that all three services can be enabled on a single ASA5515-x unit but I read somewhere t...
Hello Everyone, I have a Cisco ASA 5525-X with 9.1(3) version.My problem is: When i send the flows to a CA NetQoS, CA cannot read the packet because the ASA doesn't send the templates(image attached).So, how i can configure my ASA to send the templa...
Dear members,I want to know ifASA High Availability: one side with static ip addresses, other side with active/standby ip addresses is possible.(example inside interfaces on a HA pair with static IPs, outside interfaces with Active/standby , and wit...
Hello,I'm currently implementing Microsoft System Center 2012 Operations Manager, the curent stage of the project is to add the network devices to SCOM via SNMP in order to monitor them, I am able to add them all and monitor; however, my ASA 5510, al...
Hi Experts,Cisco ASA configuration guide says:"PAT translates multiple real addresses to a single mapped IP address by translating the real address and source port to the mapped address and a unique port. If available, the real source port number is ...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
| Subject | Author | Posted |
|---|---|---|
| 12-15-2025 09:32 PM | ||
| 12-11-2025 07:27 AM | ||
| 11-13-2025 12:52 PM | ||
| 11-03-2025 09:48 AM | ||
| 10-30-2025 12:44 PM |
| User | Count |
|---|---|
| 4 | |
| 4 | |
| 3 | |
| 2 | |
| 2 |