Hello again,One fellow asked me a question about Cisco ASA CX subscription and i'm not really sure about the answer i shall give him, so I promised him to discuss this topic here at supportforums.The thing we were talking about with him was whether y...
Hi Everyone,i was able to add the asa to csm 4.3 by add device from network.ASA is in productionAfter https connection was successfull it asked me to create ticket for that stepi created ticket need to know why this ticket creation is necessary?a...
Hi Everyone,i am trying https conenction between serevr and ASA.%ASA-6-302014: Teardown TCP connection 977425972 for inside :192.168.50.220/52438 to identity:192.168.51.1/443 duration 0:00:00 bytes 0 TCP Reset by appliance%ASA-6-302013: Built inbound...
Last week I disabled several rules on our ASA because the rules had 0 hits. Well one of the rules needed to be re-enabled to allow a department access to an application. It works after re-enabling the rule, but I don't understand why am I not seeing ...
Goodmorning all, I am trying to configure an AnyConnect solution using a pair of 5545x ASA's running 8.6 software. I am unable to access my internal network when connected to VPN. When I do a packet trace from an unassigned IP address in the VPN DHCP...
Hi Everybody,In asa 5505 there is a default dns ispection rule, like this:policy-map type inspect dns preset_dns_map parameters message-length maximum 512If I know right, the inspection check the data flows whether it is suitable for t...
any one have procedure to installation of ASA firewall in GNS3. I am not able to work with ASA in GNS3, step by step pictorial representation will be helpful for me to work with ASA firewall....
I have two Inside interfaces, Inside90 (security=90) and Inside100 (security=100)Inside100 is used only for VPN tunnels, and occasional patch updates.Inside90 is open to all internet browsingI have two Outside interfaces, Outside1 and Outside2 (both...
Hi AllProblem again. Hope you all can help to solve.I have internal server 10.200.13.1 for RDP access. But base on below config not are work.Also if bypass this firewall can work.: Saved:ASA Version 8.2(5)!hostname mkofficefw01enable password XwzHd4V...
Hi I have routing issue on ASA 5510. I have 1 interface for outside , 2 interface for inside.The issue is 2 inside interface can't route .inside 1 - 10.206.0.0 255.255.252.0inside 2 - 10.207.0.0 255.255.255.010.207.0.X subnet can't reach 10.206.0.X s...
can someone pls tell me how many interfaces in asa 5510.and can we add more interfaces to it. regards sebastan
hola estoy tratando de configurar un asa active/standby pero a su vez tratanto de que la interface failover link sea una interface redudant segun la documentacio es posible pero al configurar me indica que una interface compartida no es factible , n...
Hi all, My deployment for the firewall, there's 2 kind of user:A. local device admin for device configuration, which on can do ASDM/CLI but no VPNB. VPN only can have the attribute inherit from group policy. But if create the user with privilege leve...
Hi Everyone,For below config need to know it will do the dynamic PAT only or it will do the Dynamic NAT + PAT?object network inside_net subnet 192.168.3.0 255.255.255.0object network outhosts subnet 172.16.5.0 255.255.255.0nat (inside,outside...
Hi Everyone,Say we have webserver which has internal IP of 172.16.10.10If we need outside users from internet who need to access the webserver on IP say 200.x.x.xWe can config the NAT as below also nat (inside,outside) static 200.x.x.xRegardsMahesh
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
| Subject | Author | Posted |
|---|---|---|
| 07-16-2026 06:39 AM | ||
| 07-15-2026 08:48 AM | ||
| 07-13-2026 11:05 AM | ||
| 06-24-2026 08:00 AM | ||
| 05-26-2026 07:54 AM |
| User | Count |
|---|---|
| 2 | |
| 2 | |
| 1 | |
| 1 | |
| 1 |
