Hi everyone,I read that ASA by default do statefull filtering for TCP and UDP packets.If user access internet website then return traffic is allowed from the internet.Curious to know what config in ASA allows statefull filtering ?Or does ASA suppor...
Can I downgrade the firewall code to 8.0, it's running 8.6.1 right now.
Dear Experts,As I am planning to deploy FWSM Module in 6513 chassis and need your valuable comments regarding the strategy that I create for this deployment.Initially (Without FWSM Deployment) all internal traffic moves in this manner.7613(G9/5) --> ...
Hi everyone,Current config from ASA allows telnet to switch which is connected to DMZ of ASA from outside connection of ASA.IS there any way that i can also allow ping to this switch from outside at the same time.Can ping and telnet work at same ti...
I have a dynamic nat below that allows web traffic from specified networks in group Inside-ext to be nated to a single address below :-nat (inside,outside) source dynamic Inside-ext obj-10.50.50.1Is it possible to have multiple dynamic nat for other ...
I'm not able to start IDM on IPS-4260, i get this error message:javax.net.ssl.SSLHandshakeException: Remote host closed connection during handshake at sun.security.ssl.SSLSocketImpl.readRecord(Unknown Source)......Caused by: java.io.EOFException:...
Hi everyone,I was reading about transparent FW it says Unlike a transparent switch, however, the device will not flood frames out interfaces for an unknown MAC address destination. Instead the ASA will respond with an ARP request for a directly conn...
Hi eveyone,Need to confirm if Packet tracer is not supported when ASA is in transparent mode?or does it depend on ASA Version which we are using?ThanksMahesh
I have been tasked to connect a 2800 router to our ASA 5510 firewall. The router will be used as a VPN router. It will terminate two different VPN connections to two different networks. I can setup the 2800 VPN config but what would I need to do t...
Would like to learn from you what tools I could use in a Network that provides IPv6 visibility and also completely blocks IPv6 from being tunneled through ipv4 only networks.Scenario: I have tested this from Linux running some internal penetration t...
hi guys,I have a cisco ASA Firewall, i have some public IP's that are blocked from WAN to LAN zone, what i want is that if any user with that Blocked IP hits my firewall( tries to browse the site behind the firewall), there should be a HTTP redirecti...
Hi,I am Having cisco asa 5510 appliances with csc ssm module ssm-csc-10-k9. From last few days am facing the browsing problem and it happens twice in the week. When the problems occur i am not able to browse any internet page but on the same time i a...
Hi,I am wanting to upgrade my ASA to go to the lastest ASA code. I am running a ASA 5505 w/ 5121MB of RAM. I am looking for option on upgrading, i'm not sure I want to spend $200+ for a 1GB stick of ram.Can anyone help me? Is there cisco compatibl...
Dear All,I have error when login to IPS with the follwoing error:Error: Cannot communicate with mainApp (getVersion). Please contact your system administrator.Would you like to run cidDump?[no]:My IPS detail:Model: ASA-SSM-20Sw Ver...
Hi Everyone,I read It is important to be aware that the address assigned to the BVI is the management IP. This address will not be seen by traffic transiting across the ASA.Need to understand what does "This address will not be seen by traffic tran...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
| Subject | Author | Posted |
|---|---|---|
| 07-16-2025 04:21 AM | ||
| 07-06-2025 01:40 PM | ||
| 07-04-2025 01:59 AM | ||
| 06-19-2025 07:32 AM | ||
| 06-17-2025 01:07 PM |
| User | Count |
|---|---|
| 11 | |
| 6 | |
| 4 | |
| 3 | |
| 1 |
