Hi Everyone,If we do sh conn and it shows Connection from outside to inside Flag is aBwhere a is awaiting outside ACK to SYNwhere B is Inital SYN from Outside.Does this mean that following TCP handshakeInitial SYN was sent from outside to inside Insi...
Hi,We have an ASA 5505. 5505 comes with two default vlans 1&2 with each of them marked as inside & outside respectively.My query is , if i do not want to use vlans on 5505 and only want to use the ethernet ports as pure physical layer 3 ports, is it ...
Hi,I currently have a problem where I have to constantly reboot my ASA whenever my cable modem reboots. The ISP (Pen Tele Data) is setup so that my ASA has to obtain its' static IP using dhcp (ip address dhcp setroute) on the outside interface. Now, ...
Please i need to know if the cisco ASA next generation specially ASA 5515X support PBR or no If yes please tell me how to implement it , and if no then what is the solution here (any solution if possible please)??????------------------------Also if i...
Hi I have four Cisco ASA 5510, where by i cannot load the IOS image to Flash card I've tried a 32 MB, 64 MB and 256 MB cardI have erased disk0: and formated each card, the ios image loads ok through TFTP server into ram but im still having and error ...
i need the NAT Configuration from DMZ to InsideMy IP,s areDMZ Interface 10.1.1.1/24Webserver in DMZ 10.1.1.254Inside interface 192.168.11.249ThanksNavaz
Hi Guys,I am struggling to get successfull pings beween asa and inside hosts but couldn't succeed. Done packet tracer result is acl-dropHere is the running config..Please help!!!Prem-ASA(config)# sh run: Saved:ASA Version 8.2(5)!hostname Prem-ASAenab...
hi all,i plan to install an AIP-SSC-5 card on my 5505 and would like to know if there's any other hardware, software or RAM required?i've found that 5505 just needs to run IOS 8.2 with url below:http://www.cisco.com/en/US/prod/collateral/vpndevc/ps60...
I have several users in a local aaa setup. Logging in works, but i have to enter ENABLE to get into enable mode, and then just reenter my login password.Using the local database is there a way to log right into Enable mode from the command line?
Hi , I have 2 ASA5510-SSL50-K9, can I configure HA Failover ?
hi guys,i need lil advise ... we got two new asa with ips and licenses... as in x series it is software module except 5585x.... i have a guide on how to setup ip, upload image for ips send traffic etc etc... as ips can be setup diff ways n flavors li...
Hi There !Im in need to monitor the adclient process in Cisco ACS5.3.Coz im getting that particular service stopped sometimes.So , the workaround i am doing is Restarting the ACS Server completely.So, in-order to avoid such crap things, I would like ...
Hi everyone,Curious to know when i do sh conn it always show TCP outside to inside or TCP outside to DMZEven if i try to access the server in DMZ from outside or when i open the websites from PC behind the DMZ or inside interface.RegardsMAhesh
Hi.I have small question.If I run'reload in 1:00 noconfirm 'Does it mean, that I can make any config changes. And if I don't run 'wr mem', it reload with old config aftrer one hour?Is there any limitation running commands, i.e. can I safely make fail...
Hi guys, I have a backup server, which should backup the router configuration files securely for a list of routers. My colleagues applied this in Juniper but unfortunately am unable to figure it out on Cisco routers. The requirement is as follows: I ...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
| Subject | Author | Posted |
|---|---|---|
| 06-05-2026 10:49 AM | ||
| 05-26-2026 07:54 AM | ||
| 05-02-2026 06:09 AM | ||
| 04-30-2026 12:46 AM | ||
| 04-24-2026 07:04 AM |
