Network Security

Engage with peers and experts on network security topics such as Secure Firewall Threat Defense, Adaptive Security Appliance, Secure Firewall Management Center, and Security Cloud Control.
cancel
Showing results for 
Search instead for 
Did you mean: 
cancel

“Join

 
Labels

Forum Posts

Hello, everyone,I  ran into a very strange icmp ping issue that I could not seem to undersatand, hope someone can provide a troubleshooting tip on this. The network has been working fine other than the issue listed below, L2L VPN worksfine and all t...

bc4switch by Level 1
  • 9466 Views
  • 5 replies
  • 0 Helpful votes

Dear All,             We have FWSM running  4.1(7) system software. It has multiple contexts.Our DB team is initiating backup of DB (around 10-11 TB) from one server (WEB-CONTEXT) to another server (PROD-CONTEXT), it takes a week or sometime it takes...

Hi,I'm to move devices behind the firewall and there are about 50 vlans that i need to move behind the firewall so there would be able 50 subinterfaces.creating 50 subinterfaces & so ACL for each subinterface sounds like a lot of work and alot manage...

gavin han by Level 1
  • 865 Views
  • 1 replies
  • 0 Helpful votes

I'm curious if there is a way to stop tunneling applications out HTTPS with ASA 5500. I know everything is encrypted but is there a way to at least inspect the traffic to make sure it complies with RFC 2818? Perhaps there's another way to provide s...

snickered by Level 1
  • 1046 Views
  • 2 replies
  • 0 Helpful votes

Hello Basically after upgrade from ASA 8.4 to 9.0 (2) I have problems when certain types of NAT.Example:ASA 8.4:      nat (LAN, outside) 85 10.252.253.123 source static 192.168.3.2 192.168.3.2 192.168.3.104 static destination service http http In thi...

I've upgraded some old PIXen to ASAs running 9.1(1) in the past few months, and have seen plenty of these:Apr  8 16:33:32 myasa %ASA-4-733100: [ Scanning] drop rate-1 exceeded. Current burst rate is 13 per second, max configured rate is 50; Current a...

hi therei have network 10.7.10.0/22 conected by mpls router and conected by cisco router adsl for internetip for mpls router 10.7.10.1/22ip for adsl 10.7.10.2/22i want to install and configure cisco asa 5510 newi cannot access to thes routers so i ca...

Hello,I'm trying to configure some firewall rules and a nat in our pix 525 and I'm having some issue with the connectionHere are the details:172.40.40.40 destination host.1.- I configured an ACLACL test 172.80.0.0 255.255.0.0 destination 172.40.40.40...

Hi, I am very much confused on which IPS model is included on ASA 5515 X series, part no. ASA5515-IPS-K9. I guess they include AIP SSC 5. I am looking for AIP-SSM-10 or AIP-SSM-20 feature. Can we get this kind of feature by adding licence or not on t...

Here is the scenarion:- would like to route any internal traffic thats SMTP based only to internal email server ( x 2 ) - The default gateway is already set on the email server to go out the outside interfaceCan this be done on an ASA, I am thinking ...

mingram27 by Level 1
  • 509 Views
  • 3 replies
  • 0 Helpful votes

Has anyone experienced a slowdown in VMWare (v5) VDI with PCOIP screen refresh rates when the traffic goes through a Cisco ASA firewall (version 7.? - I'm not at work as this question came to mind.)  Any special commands one might be able to put in p...

mmedwid by Level 3
  • 1291 Views
  • 7 replies
  • 0 Helpful votes
Review Cisco Networking for a $25 gift card