SALAM ALEYKUM.Please, can you give me step-by-step official or unofficial (official more preferable) guide about upgrading IOS from 8.2 to 8.4 on ASA 5520 model?
SALAM ALEYKUM.Please, can you give me step-by-step official or unofficial (official more preferable) guide about upgrading IOS from 8.2 to 8.4 on ASA 5520 model?
Hey Guys,I'm experiencing a weird ACL issue and I'm clueless about the possible cause. I have two switches running HSRP for VLAN 400 (might not be relevant, but I thought I'ld mention it anyway). Since this VLAN runs production devices, we have ACLs ...
I am very new to the Cisco IPS front and have setup a ASA 5510 with the SSM-10 IPS module. We have one interface enabled with multiple VLANs on this interface. I have setup the IPS, to the best of my abilities, and I believe it is correct as inline...
Looking for anyone that might have a clue in on this, im attempting to configure a pair of routers to use WCCP to redirect HTTP and HTTPS traffic to two content keeper devices. The network im building is going to be used for a guest internet connecti...
I have two ASA 5505 devices that I am using for a site-to-site VPN. When I went to the remote site, I was able to connect everything and had it working until about two weeks ago. This was about 3 weeks after the install. Here are the results from "sh...
Hello, I came up accross a weird situation when I was trying to apply a self signed cert to my SSL_VPN group as a test.Here is what I came accross...the command that I needed to use was "trust-point self" under my SSL_VPN group.[code=..]tunnel-group ...
Anyone ever seen a message like this?We're running v8.4(2) on a 5520. We detected no other anomolies around that middle-of-the-night timeframe.
hi everyone,unable to connect to device on port 27000.here are logs: %ASA-6-302013: Built inbound TCP connection 69552007 for X:172.x.x.x/64755 (172.x.x.x/64755) to Y:172.x.x.x/27000 (172.x.x.x/27000)%ASA-6-302014: Teardown TCP connection 69550694 fo...
Hi All,My syslog is full of %ASA-4-106023: Deny tcp src outside:---- by access-group "inbound-acl" messages. I did not configure an explict deny for the access list to log these denies.Can someone explain how I can disable logging of denied connecti...
Good Morning, Has anyone done an upgrade from firmware 8.21 5o 8.31? I am installing 1GB of memory in my ASA 5510 and in the process I have upgrade the firmware.- Will the upgrade change my configuration or will I have to change this manually myself ...
Hi,i have ASA multicontext and transparent in Active/Standby mode, failover is OK, i dont have managment ip address the firewall is managed by ip address assigned on inside context.config.:inside context (admin context)ip address 10.1.1.1 255.255.255...
If I configure an ASA, let's say the g0/1 port with a static ip address of 192.168.1.1 and assign it to the inside network, make g0/0 my outside connection, my question is if I have 2 workstations which will have a static ip address on the 192.168.1....
hi all,can i copy running-config to another file in the flash, do testing on it, if something goes wrong, put it back. like...asa>copy running-config my-configtesting...revert...asa>copy my-config running-configasa>reloadis it like that?thanks!
We are deploying AP's with 802.1x ports. We do not want ot have static AP ports. When plugged into a switch port with 802.1x configured the AP does not kick up the smart port trigger. How do I link the trigger from ISE to send the ...
Hi guys I have some problem to get working ACLs. The main purpose of this ACLs is to control what is going out from vlan to internet. (For example, i want that only my proxy can access to the web.) So, i use Cisco Packet Tracer and test new rules in ...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
| Subject | Author | Posted |
|---|---|---|
| 06-24-2026 08:00 AM | ||
| 05-26-2026 07:54 AM | ||
| 05-02-2026 06:09 AM | ||
| 04-30-2026 12:46 AM | ||
| 04-24-2026 07:04 AM |
| User | Count |
|---|---|
| 2 | |
| 2 | |
| 1 | |
| 1 | |
| 1 |