Hi,I'm looking for a way to avoid doing 999 individual port address translations for ports in a range 1-999 for the same protocol. I'm not finding anything that asa code v9.11 will allow. I have the service objects defined but cannot find a way to ge...
Dear ExpertHello.Could you tell me about Cisco Configuration Professional. I'd like to try the IOS-IPS on Cisco2901-SEC/K9.I was search in CCO about Cisco Configuration Professional.The Cisco2901-SEC/K9 does not support SDM.But, The Cisco2901-SEC/K9 ...
ASA Version 9.1(1) !xlate per-session deny tcp any4 any4xlate per-session deny tcp any4 any6xlate per-session deny tcp any6 any4xlate per-session deny tcp any6 any6xlate per-session deny udp any4 any4 eq domainxlate per-session deny udp any4 any6 eq ...
Sorry for this question but my knowlege of switching and router is still growing.We have a HP Procurve 5412zl switch as our default gateway for all our VLANs from there the traffic will be going to a Cisco ASA 5515 and then to a Cisco 3800 Router t...
Hello Experts,I've been having a few problems with cisco's AnyConnect. Installing the package normally didn't work so I copied the installation files from a desktop where it worked successfully.Each time execute the application from the copied files ...
I have a website with very high hit rate which is protected by IPS. There've been complains about some dropped request so I've gone through IPS Event Viewer and I found many of this:evError: eventId=1321353761353146007 vendor=Cisco severity=error ...
Hi,I'm trying to upgrade ASDM 6.2(3) F in FWSM 4.0(4) but after transfering new image file using TFTP and saving the configuration show version command is still showing older version of ASDM.6.1(2) FIs FWSM reboot required ? which sounds stange to me...
Hello CommunityCan someone show how to connect to SSL VPN within Cisco ASDM?Normally, I would connect with cisco's AnyConnect, but because Cisco ASDM is installed I'm unable to install AnyConnect, so would like to connect using Cisco ASDM CheersCarlt...
Hi all,Can you anyone tell me the command to view current anti-reply window size in ASA 5510?
Hi,I need to replace two small firewalls with an ASA. The ASA will need to support static PPPoE and dynamic PPPoE on different outside ports. I'm looking for an example of either configuration and confirmation that the ASA can handle this setup (not ...
Hi, I'm using ASA 5515X my concern is I was not able to block the traffic of P2P such as BitTorrent etc. I was also view some technotes on how to use webfilter without using Websense or Smartfilter tools and lucky I'm able to block certain websites. ...
Dear All,I need your opinion regarding moving of IDSM -2 and FWSM Module from 7613 to 6513 chassis.Currently these two modules are in 7613 and we are not using either of them now we have to configure them in 6513 chassis. As you can see from the figu...
Hi,I need to configure NAT in my firewall. But I face one problem due to different vlan's.example:int g0/0 ( LAN of vlan 10) ip nat inside ( what to configure)int g0/1 (WAN) ip nat outside.
Hi,I have a small lab setup with the ASA connecting to an 887 router (for internet) and a 3550 switch for LAN. I am also trying to setup two routers in the internal network that need to be accessed from the internet for DMVPN. Both routers can access...
Hi All,I want to achieve the below scenario with static NAT.1. I have a firewall which is having two legs ( inside and outside). As usual inside security is 100 and outside is 0.We have done a PAT for all the inside networks to access the outside net...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
| Subject | Author | Posted |
|---|---|---|
| 07-16-2025 04:21 AM | ||
| 07-06-2025 01:40 PM | ||
| 07-04-2025 01:59 AM | ||
| 06-19-2025 07:32 AM | ||
| 06-17-2025 01:07 PM |
| User | Count |
|---|---|
| 11 | |
| 6 | |
| 4 | |
| 3 | |
| 1 |
