Network Security

Engage with peers and experts on network security topics such as FTD, FMC, FDM, CDO and ASA.
cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
Labels

Forum Posts

Resolved! MS IE toStaticHTML String Parsing Cross-Site Scripting Vulnerability alarms

Hi, I was wondering if someone else has noted an increase in false positives concerning the following 2 events:- Microsoft Internet Explorer toStaticHTML String Parsing Cross-Site Scripting  Vulnerability- Microsoft Office Excel Ghost Record Parsing ...

Resolved! asa log

Hi,Few questions on ASA:1. one of asa  has logging enabled for warning & information message.   logging enablelogging buffered warningslogging asdm informationalwhen asdm logs are seen, it shows normal teardown etc. for traffic. but sh log gives lot ...

suthomas1 by Frequent Contributor
  • 902 Views
  • 7 replies
  • 0 Helpful votes

Resolved! 3DES may be faster

Even though AES has theoretical advantage over 3DES for speed and efficiency in some hardware implementation 3DES may be faster where support for 3DES is mature.http://blogs.msdn.com/b/ace_team/archive/2007/09/07/aes-vs-3des-block-ciphers.aspxI have ...

lcaruso by Frequent Contributor
  • 7089 Views
  • 5 replies
  • 0 Helpful votes

ike command issue

when I do any changes on firewall, I get following error in logs,it gives me message that below parameters are not updated in firewallset ike ikev2 initiator-send-dummy-ipsecset ike ikev2 ike-sa-soft-lifetime set ike ikev2 stateless-cookie-threshold ...

Jigar Dave by Participant
  • 375 Views
  • 3 replies
  • 0 Helpful votes

Routing failed to locate next hop

Hi everybody, last week I had a problem into my network, now is working fine, but I want to know if you can help me to know what was the possible reason for that problem and which of my actions was the one who  fixed the problem, and/or if it can pas...

COST89010 by Beginner
  • 1015 Views
  • 9 replies
  • 0 Helpful votes

Resolved! asdm error

I'm trying to enable the top ten services feature using asdm 6.34-53 and get the error in the attached graphic.I assume this means threat detection is not compatible with this feature? Is there a way to work around this?

lcaruso by Frequent Contributor
  • 772 Views
  • 3 replies
  • 0 Helpful votes

Resolved! Inaccessible Links

There are various links posted by support personnel in the "Ask The Experts" discussion that I cannot access. A few examples:http://www.cisco.com/en/US/partner/docs/security/ips/7.0/configuration/guide/ime/ime_getting_started.html#wp1233087http://www...

jaysoo by Beginner
  • 401 Views
  • 2 replies
  • 0 Helpful votes

IPS signatures

Can somebody help me to get brief information on the below signatures. DCERPC: Frag Length Overly Long-0x47600a00 TCP: ACK Host Sweep-0x40009c00NETBIOS-SS: Guest Login Succeeded-0x4070a500 NETBIOS-SS: NULL Credentials Login-0x4070a400 DCERPC: Spoolss...

vijayyada by Beginner
  • 1020 Views
  • 1 replies
  • 0 Helpful votes

exchange interfaces on Cisco ASA

Hi all,I have this configuration:interface Ethernet0/0 nameif outside security-level 0 ip address x.x.x.x 255.255.255.224 standby x.x.x.yinterface Ethernet0/2 nameif dmz security-level 95 ip address y.y.y.y 255.255.0.0 standby y.y.y.zEthernet0/0 is a...

gdspa by Beginner
  • 6501 Views
  • 4 replies
  • 0 Helpful votes

ASA Configuration Examples

Hello Everyone,I have a ASA 5550.I need to configure three points:• Automatic Backup(if it exists).• Log shipping to a syslog server(it server can a Cisco Works version 3.2?).These points can help me?The configuration of sending logs to a syslog serv...

FWSM in Cisco 6500 - High CPU usage

Hi Guys,We have a Cisco Catalyst 6500 with a FWSM running V 4.0(6)We have noticed that when we apply new rules into the ACL (through ASDM or CLI) that after the ACL is applied,the CPU sits very high (90-100%) for up to 20 min.During this time, the ne...

dneggers1 by Enthusiast
  • 4835 Views
  • 13 replies
  • 0 Helpful votes
Getting Started

Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: