Hi all,Let's begin with the elephant in the room... YES, I know the ASA 5525-x is eol but i have a few of them laying around and i wanted to place them in a homelab to play around with. I would like to download the latest firmware for the device but ...
Hello.so i'm in the middle of an assignment and i've started getting MAC flapping on my port channels.i cannot for the life of me figure out how to get it to stop.most of what i've read is to setup spanning tree, but i'm not sure exactly how to do th...
HI, I want to migrate a high-Availability ASA 5515 to Firepower FTD in FMC with the migration tools. I know that HA is not supported by the tool. What is the best way to do it, Create 2 standalone ASA , migrate both of them and after that create th...
What happen if the front 100gb ssd died. Or if i buy one without it. Will get an frd2110 free from work… I’m not finding documentation about this. Their is a lot doc about the second sdd. Will the ftd 7.4 code run correctly? Or it will be in some kin...
Hello,I'm working on getting information about my organization's cisco firepower 2140 devices. I am stuck on getting the device's serial number, tried oid: 1.3.6.1.2.1.47.1.1.1.1.11, but the trap returns empty. I've tried to google for it the last co...
Hi Cisco Experts! Good Day! Our Firepower sensor in Cisco 5516-X is not accessible anymore in ASDM. I can access ASDM with all firewall configs still intact. Only missing is the SFR configurations. Usually under Firewall Configuration, I could see ...
I am having issues with my ASA not transferring traffic from VPN subnet to internal subnet. VPN is 10.1.1.0/24 subnet and internal is 172.16.10.0/24 subnet. : Hardware: ASA5506, 4096 MB RAM, CPU Atom C2000 series 1250 MHz, 1 CPU (4 cores):ASA Versio...
We have FMC-FTD RAVPN with LDAP realm just like in https://www.cisco.com/c/en/us/support/docs/security/anyconnect-secure-mobility-client/216955-configure-ad-ldap-authentication-and-u.html#anc17 The Identity policy contains the LDAP realm. The user-ba...
firepower configurationSupervisor Mgmt IP Address = 10.10.1.10Supervisor Mgmt IP Network = 255.255.255.0Default Gateway = 10.10.1.1SSH Access Configured =yes SSH IP Address= 10.0.0.0SSH IP Netmask= 255.0.0.0 HTTPS Access Configured=yesHTTPS IP Addres...
2 Firewall ( FTD ) with Same IP possible to manage from same FMC ? I have a situation, where i am placing a second FTD in my DR with same IP and Config as similar to On Premise FTD. But would like to add the DR FTD in same FMC where On Premise FTD is...
Say I have a FMCv (running in VMware) managing about 20 FTD firewalls (1k and 2k models) currently. I want to plan to move my existing FMCv to cdFMC within CDO. Is there a way to migrate the existing FMC configuration, such as the policies and object...
There was an issue with uploading the new image to the backup FMC. To find out why I want to access the FMC via cli and find the password wrong. So, I have checked the document to reset the password. After rebooting the host with single mode, try to ...
We have a number of FPR2110-NGFW-K9 in different zones in a network. They are standalone and not managed by any controller (one fw in each zone, data-diodes between zones).The fw's are sending syslog to our loggserver but there isn't any host informa...
Hi all,Customer has two 1120's running in single mode and in active/standby failover configurationnow i would need to put them into multi context modei tried first to put the active into multi context mode (via console)it starts as expected:pri/act/a...
Hi everyone,I have some questions about ports and communication serial.1.- What does it mean "Segmentable network port"?2.- What standards about Network Security apply on "Serial Port"?My technical Specification of my device are:I really appreciate y...
