I am trying to introduce an ASA5520 to my network based on the following diagram: ISP Internet ------> ASA5520 ------- > Cisco Router ------> LAN. The problem is I cannot ping the ASA from the LAN. I can ping it from inside the router. I already ...
I have 2 535's in failover mode. Last week the primary outside interface went into a line down state. No changes were made to any configurations and this had been running for years. I have rebooted both PIX's and still get the same down state. inte...
Hello,The AIP-SSM Module installed in the secondary firewall is down.Any thoughts to fix thisRegards,irfan
I ' m not able to configure the asa 5510 to allow the multicast traffic to pass through ASA.The multicast traffic have to pass from inside interface to outside interface.Can I configure the multicast traffic to pass through asa with a static nat ?Can...
Could someone point me in the right direction and maybe provide a config example of how to setup an ASA with two Internet connections? We want to have the ability to send certain traffic over one connection (example http) and everything else over an...
Alright, well I have a Cisco 891w router and have just about everything up and ready to deploy. I'm primarily using Cisco CP 2.4 to provision the router with minor tweaks being done in the CLI. I want to set up a filter to allow access to roughly 20 ...
Hi Friend,I need to translate one host ip into an another network IP to access the host.For example:I have host A in X network and need to access the A host in Z network through ASA 5510 Ver 8.3 firewall.I have done the Static Nat configuration, but ...
Where is it supposed I have to set embryonic limits? in the static command or with a class-map? what is the difference?andHow can I monitor embryonic connections?Thanks
Hi,AIR-AP1121AG-A-K9 is not getting connected to WLC.
Hey,New to Pix and Cisco in general. I have had the PIX 525 for about 4 months now and have managed (with the help of people on this forum) to get it to do what I want for the most part.I have recently had a lot of hacking attempts being made on my n...
Himaybe a stupid question.ASA v 8.2What does the ACL hit count count ? I always thought that the acl hitcount counted the numbers of packets hitting that line in the ACL, however that is not the case.if I setup a icmp permit rule then that will only ...
Dear, I am trying to enable TCP ports 50,000 to 60,000 for my voice gateway placed in DMZ (Security level 50) from Inside (Security level 100)Please see my configuration attached.By default, Inside to DMZ is all allowed because of security level appl...
Hello Support,We had create one remote access VPN and now we want to upload file from remote desktop (client) to server, could you suggest how we will do this task.
We have a Cisco 891 with this configuration belowI got several computer on my lan that needs to connect to an external Windows server with pptp. The windows server is not mine but it works. The clients are using the windows connection manager....
Hi All , I am try to install cisco vpn client 5.0.1 on windows 7 64 bit operating system , But installation fails due to internal error . which is correct VPN client for windows 7 64 bit operating system
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
| Subject | Author | Posted |
|---|---|---|
| 05-05-2026 09:59 AM | ||
| 05-02-2026 06:09 AM | ||
| 04-30-2026 12:46 AM | ||
| 04-24-2026 07:04 AM | ||
| 04-22-2026 11:56 AM |
| User | Count |
|---|---|
| 6 | |
| 3 | |
| 1 | |
| 1 | |
| 1 |
