Network Security

Engage with peers and experts on network security topics such as Secure Firewall Threat Defense, Adaptive Security Appliance, Secure Firewall Management Center, and Security Cloud Control.
cancel
Showing results for 
Search instead for 
Did you mean: 
cancel

“Join

 
Labels

Forum Posts

Dear's,The Supported device list below by cisco does'nt support Express 500 as a Edge deployment but in my network i m having Express 500 and they are passing packets through NAC they are supported.How ?????????  Can anybody brief me abt this.Also ca...

Resolved! ASA port redirect

Hi All,I am trying to replace an apache proxy server that redirects traffic from 192.168.250.16(apache IP) to 10.195.23.13 (remote host)The IP of interface VLAN107 is 192.168.250.254The idea is to have clients connect to the Interface IP of the asa (...

I have a Cisco 2600 and would like to block traffic from hinet.net by hostname. does anyone have any suggestions?Thanks,George Christiansengeorgarthr@verizon.net

Hello Everyone,I am going to be implementing an HA Cisco IPS appiiance using inline mode.This is my diagram..                         SWITCH 1   -----------------  SWITCH 2                               |                                    |         ...

Hello, I have a question about what will trigger a standby interface to become active in a redundant interface configuration on an ASA. On my ASA5540, I have 2 physical Ethernet ports configured as a single redundant interface The Active ASA physical...

Hi All,I have 2 ISP links and i want to make them as active standby links for the ASA for internet access.it it applicable and if so how can i do itThanks in advance,Ayman

/* Style Definitions */ table.MsoNormalTable {mso-style-name:"Table Normal"; mso-tstyle-rowband-size:0; mso-tstyle-colband-size:0; mso-style-noshow:yes; mso-style-priority:99; mso-style-qformat:yes; mso-style-parent:""; mso-padding-alt:0in 5...

lcaruso by Level 6
  • 1048 Views
  • 2 replies
  • 0 Helpful votes

Resolved! NAT configuration.

Hello,I need to NAT my internal server and allow traffic to 2 vendor servers on ports 443 and 80. I'm using ASA 5510. Can you please confirm that the following lines are the way to configure this scenario:my internal server's IP: 10.10.10.10/16public...

forman102 by Level 1
  • 587 Views
  • 1 replies
  • 0 Helpful votes

Hi, Could you please help to advise? I have issue on my project . I have already setup the ASA 5510 and configured eth0 for outside ( security-level 0) , eth1 for DMZ (security-level 50 ) and eth3 for internal network ( security-level 100 ). I want t...

Dear,I keep getting the following warning from the ASA ASDM syslogDuplicate TCP SYN from inside:192.xx.xx.xx/63993 to outside:xx.xx.xx.xx/25 with different initial sequence number. The client in question sitting on the inside of the ASA is trying to ...

cisabucho by Level 1
  • 4892 Views
  • 2 replies
  • 0 Helpful votes

Hi there,I have an ASA5520 firewall and have the following already in place :name 123.123.123.123 EXTERNAL-NATaccess-list OUTSIDE_OUT extended permit tcp host EXTERNAL-NAT host xxx eq 5061 access-list OUTSIDE_OUT extended permit udp host EXTERNAL-NAT...

HelloGot a 5520 with all the clients coming in on one interface and got a few other interfaces with servers behind them. In our group we are discussing how set this up with access-lists and or security levels.1: is to set lower security levlel on the...

Review Cisco Networking for a $25 gift card