Hello,I have created Time range in Object Management from 08:00 until 09:00 AM and inserted into created rule from outside to inside PC allow connection for the specific time mentioned before. I`ve checked time zone and synchronization on FTD and FMC...
Forum Posts
Hi all, I have a cluster of 2x FTDs running on 2130 with version 6.4.0.9 which is managed by my FMC. In the threat defense policy which is applied to my FTD cluster, the Secure shell settings in my platform settings is blank but i am able to ssh into...
Hello All, We have two Firepower 2110 appliances with the ASA code and I want to re-image the appliances with the FTD code 6.6 or 7 so my question is when I do the re-imaging and add them to the FMC do I need any type of licenses to configure them as...
I have a Firepower 2120 running FTD 7.3.0-69, using FDM. I've tried to enable FIPS in the CLI but get the below error. /security # enable fips-modeWarning: Connectivity to one or more services may be denied when committed. Please consult the product'...
Hello I performed upgrade on my ISR1K and ISR4K spoke router. DMVPN didn't come up until I deleted command "if-state nhrp" under tunnel interface. It stuck i NHRP state Does anybody have an idea why? Regards, Emina
Hi, Is there a possibility to disable SSL 2.0 & 3.0 & enable TLS 1.2 in following devices Devices - IOS versions ACE-4710-0.5F-K9 - A 3(2.7)CSACS-1121-K9 - 5.1.0.44WS-C2960S-24TS-S 15.0(2)SE11 Thanks in Advance...
We are having a heck of a time trying to deploy FMC in Azure with any of our 100+ CSP subscriptions. The validation fails saying: Offer with PublisherId: 'cisco', OfferId: 'cisco-fmcv' cannot be purchased due to validation errors. For more informatio...
hi,Issue:Had to rebuild and restore a vmware FMC from an old backup. Now but my FMC won't upgrade and can't connect to Devices? My vmware FMC running 7.0.3 had an issue with its database and TAC recommended to restore from a backup.Built a new vmware...
Hi Community, All of a sudden i am unable to access the GUI of FMC with admin credentials though i am able to access it through CLI.Has anyone experienced this issue & what could have triggered this.Any solution pls. Thanks,
I am trying to block a TLD utilizing the ASA. I would ultimately like to block something like .mail but not necessarily mail.com. Any ideas?
Hello Everyone, I am not able to open http and ASDM. can someone guide me what causing the issue. FYI: CISCOASA: 5510ASDM file into dir (disk0:/): asdm-782.binASA5510# sh asdm imageDevice Manager image file, disk0:/asdm-782.binhttp server enablehttp ...
I'm trying to restrict access to the management interface of a pair of 1150s running 7.2.0. I've run the following command: configure ssh-access-list 8.8.8.8/32 which appears to complete successfully("The ssh access list was changed successfully."...
Resolved! ASA5510/ asdm compatibility
Hello everybodyI lost asdm523.bin image for asa723 and i couldn't find link to download it can anyone give me the link to download or ASDM compatible for asa723.thank you.
Hi, Everyone:After done some troubleshooting and data capture, and found out Intrusion event syslog for message ID 430001 is sending to destination port (udp 514), I could see other message ID (430002, and 430003) are sending to udp port 1515, since ...
Hi Im tasked to move an HA 4115 FTD to a new FMC. We are going from Physical to Virtual so sadly this does not comply with the supported fmc model migration path shown here: https://www.cisco.com/c/en/us/td/docs/security/firepower/fmc_model_migration...
