Hi,i´m quite a newbie to PIX, normally i work with Switches or routers!I´ve got some CISCO PIX 506E with Version 6.3(5).Some of them have to be downgraded to the PIX Version 6.3(3) and 6.3(1).I already searched the web, and cisco.com but found nothi...
Hione of our machine behind asa5520 have strange behalve. the log is:Deny TCP (no connection) from 10.10.10.5/39708 to 10.10.5.5/22 flags RST on interface insidemy configure is:object-group network mytest network-object 10.0.0.0 255.0.0access-list o...
Hi All,i was going thru yusufs Network security technology and solutions book and it says flash memory size has to be the same on both units doing failover but in the CERT flash cards for CCIE security it says flash memory size does not have to be th...
Hello, I have a Cisco PIX firewall 515E version 6.3 connected on one interface (eth1) to a linux PC (200.0.10.5 in subnet 200.0.10.0/24) and on the other (eth0) to a SoHo router (interface IP 200.0.11.2 in network 200.0.11.0/24 - behind the rout...
Hi.Help me please to undestand.I have OOB mode on next equipment:CAM 4.7.2CAS 4.7.22811 routerwin2008r2 enterpriseLinksys srw2008mpCatalist 4000same hosts: winxp and win7 with nacagent 4.7.2AD SSO on CAM started, ports on switch is controled.On layer...
Hi GuysFirst time so I hope I'm in the right area.Installed CNA v5.5 on my laptop. Using XP SP3. CNA runs. However, when I've entered an IP address of a switch it closes the application down. I don't get a box asking for ID and password.Any ideas mos...
Hi,Does anyone has such problem?I can connect to the Remote Access VPN via internet successfully and RDP or ping any hosts from the ASA firewall Inside Interface but if i use IPhone tethering via USB on my laptop, it can connect to the remote VPN suc...
I have been attempting to get NAC deployed in the last month. I have come up with a few issues.I upgraded to 4.8 and that went smoothly. I have an in-band deployment and will be using an ASA VPN connectionsonce I get everything working correctly. ...
Hi All,Have 2 2800 series routers here that are at either of our sites. They had been setup with ip inspect statements for various traffic types however when we try and remove them completley they break various different protocols inlcuding web brows...
Following the URL below I setup netflow on my ASA to be able to analyze traffic through the firewall. My netflow analyzer is Solar Winds Netflow Traffic Analyzer buit it is not perceiving receipt of the packets although I know from wire shark they a...
Hi ,i have installed IPS 4255 with version 7.0(2)E4 and using IME 7.0.2.i am not able to see the logs in the IME (Event Monitoring), but when i access it by CLI (show events) i can see the logs.i also tried to tune a signature for ICMP large packet t...
We are configuring an ASA5510 for the first time. However, we seem to have hit a wall. There seems to be no communication between the interfaces at all. We have played with the static routes and access rules to no avail, it just seems like nothing...
When configuring Active Standby ASA firewalls do you need a standby address? The problem I have is that we have a single customer WAN link with single IP address but two firewalls.I think the answer to my question is not to configure a Standby addres...
I have some network monitoring servers that are using snmp/icmp to monitor devices on the network. The icmp functions are not used but can not be turned off on the application so are blocked on the firewall. This is filling the logs on the ASA with...
Is there a way to prevent the Floating Toolbar from popping up? We are using ASA 7.2(2)ThxZhenning
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
| Subject | Author | Posted |
|---|---|---|
| 05-16-2025 07:07 PM | ||
| 05-16-2025 05:41 AM | ||
| 05-16-2025 04:23 AM | ||
| 05-15-2025 09:59 PM | ||
| 05-13-2025 11:57 PM |
| User | Count |
|---|---|
| 3 | |
| 2 | |
| 2 | |
| 1 | |
| 1 |
