HelloI'm trying to establish a IPSEC tunnel between FTD 2130 and Umbrella SIG either using Policy Base our Routing Base tunnels, and neither of them are working for me. My FTD is on code 7.0.1.1I am seeing on Umbrella documentation that their is no m...
Forum Posts
Hello, I have a vpn tunnel from my servers behind a cisco to my azure server. I have to ping from the servers behind the cisco to the azure before I can ping from the azure to the cisco.
Hello CISCO Community I wanted to ask what SIEM (Security Information and Event Management) software they use aside from 'Splunk'? that works well with CISCO networking product
Hi. I try to upgrade my cisco catalyst 3850 from ios xe 3.3.6e to 16.3.9. But i have this issue and switch doesn’t boot. Bootable image at @ ram:0x53430388Bootable image segment 0 address range [0x81100000, 0x81b8adc0] is in range [0x80180000, 0x900...
Hi.We currently have a Cisco FMC operating out of Datacenter (DC1) running on version 6.4.0.14 (Build 67) and now there is a requirement to migrate this off the current ESX environment (to be decommissioned) to another DC's ESX environment. The Cisco...
I have virtual FMC and two FTD 2120 boxes. Version is 7.0.5. I want to see Interface statistics in Health Monitoring. But there is a statement "Throughput module is disabled in the health policy". I was looking in health policy for this two FTD, but ...
Hello, I'm trying to get passive identity to work with FMC, but I'm a bit stuck. So far I have a working PXGrid connection between FMC and ISE and I have also configured the Realm and an identity policy in FMC. All those things seems to work and I ca...
Hello, I came across some similar threads and none seem to solve this problem. We are facing the below error on FMC 6.4.0.10 since almost 2 months ago: Here are the expired Cisco AnyConnect Apex licenses shown in the Smart Account, although we are n...
Hello,Can anyone point me to a known working method of staging a FPR1010 offsite and then shipping to site preconfigured to be managed remotely either with FMC at a different site or CDO? This site will not be using the built-in mgmt. port, so everyt...
Resolved! Cisco FMC NAT
Hi,I am facing some NAT config issues; the scenario is as follows:I have a vm server(3.20) in AZurDC wants to access to URLs with another entity via ISP tunnel. I have a single NAT ip address(60.43) which is being natted on the FMC with NAT policy 1 ...
Good day! At work i have cisco as 5506 (ver 9.6(1)) actually configration is working. i have 3 differnece inside network (2 of thm vlans) and 2 isp ( one isp is now out of service). at vlan 10.103.2.0 int 2.1 is gateway for this network and confiured...
Say I have a pair of FTD 4k with two container instances running (v7.2). Each instance is running HA between the two physical appliances and each instance has etherchannel made of two interfaces. From what I read, the individual interfaces can be ad...
It is my understanding that using "crypto key generate rsa" will generate two keys for use with SSH. One is a private key stored in NVRAM which cannot be accessed, and the other key is a public key. I believe this command should generate one general...
Resolved! Cisco ASA Active Standby
Hello All,I'm doing a lab in my GNS3 just built ASA active and standby which is no issues but when i try to access the outside ip address which is the ISP i cannot ping it from inside interface but there is no proble from outside interface.I though i...
I have a Cisco Firepower 2110 and would like to have a backup internet connection. I don't want it to be a redundant system, I basically just want it as a fail safe in case our primary internet connection fails. Example, to be clear: If Ethernet1/...
